Residual Risks; Saw Blades - Stanley FATMAX FME720 Manual Del Usuario

ENGLISH
● Make sure all locking knobs and handles are tight before
starting any operation.
● Never use your saw without the table insert.
● Never place either hand in the blade area when the saw is
connected to the mains supply.
● Never attempt to stop the machine in motion rapidly by
jamming a tool or other means against the blade; serious
accidents can be caused unintentionally in this way.
● Before using or fitting any accessory consult the
instruction manual. The improper use of an accessory can
cause damage.
● Do not use any abrasive discs.
● Raise the blade from the table insert in the workpiece prior
to releasing the on/of switch.
● Do not wedge anything against the fan to hold the
motor shaft.
● The blade guard on your saw will automatically raise when
the arm is brought down; it will lower over the blade when
the arm is raised. The guard can be raised by hand when
installing or removing saw blades or for inspection of the
saw. Never raise the blade guard manually unless the
machine is switched off.
● Check periodically that the motor air slots are clean and
free of chips.
● Do not work with material containing asbestos. Asbestos
is considered to be carcinogenic.
● Never make the warning signs on the power
tool unrecognisable.
● Never stand on the power tool. Serious injuries could
occur when the power tool tips over or when coming in
contact with the saw blade.
● Do not take hold of the saw blade after working
before it has cooled. The saw blade becomes very hot
while working.
● Advance the saw blade against the workpiece only when
it is switched on. Otherwise, the danger of kick-back exists
when the saw blade catches in the workpiece.
● The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
● Never place hands near cutting area. Keep hands outside
the "No Hands Zone" which includes entire table and is
labelled by "No Hands" symbols.
● To avoid injury from materials being thrown, unplug
the saw to avoid accidental starting, and then remove
small materials.
● Before use and after any maintenance the blade guard
must be checked to ensure proper function. This test must
be performed with the saw switched off and unplugged.
The arm must be raised and lowered to ensure the guard
covers the blade and the blade does not contact the
guard. If the guard fails to operate correctly, have your
power tool serviced by a qualified repair agent.
10
(Original instructions)
● Call Stanley Fat Max customer services for you nearest
service agent.

Residual risks

The following risks are inherent to the use of saws:
● Injuries caused by touching the rotating parts.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
● Impairment of hearing.
● Risk of accidents caused by the uncovered parts of the
rotating saw blade.
● Risk of injury when changing the blade.
● Risk of squeezing fingers when opening the guards.
● Health hazards caused by breathing dust developed when
sawing wood, especially oak, beech and MDF.
Additional safety instructions for lasers
This laser complies with class 1M according to IEC 60825-
1:2014. Do not replace a laser diode with a different type.
If the laser is damaged, have the laser repaired by an
authorised repair agent. Do not use the laser for any purpose
other than projecting laser lines.
● Never look into the laser beam directly and intentionally.
● Do not use optical tools to view the laser beam.
● Do not set up the tool where the laser beam can cross any
person at head height.
@
● Do not let children come near the laser.
Warning! Avoid direct eye contact. Laser
radiated when laser guide is turned on.
Avoid direct eye contact. Always un-plug the
mitre saw from power source before making
any adjustment.
● A laser pointer is not a toy and should not come into
hands of children. Misuse of this appliance can lead to
irreparable eye injuries.
● Any adjustment to increase the laser power is forbidden.
Any liability for damages as a result of not following these
safety instructions will be rejected.
● When using the laser pointer, do not point the laser
beam towards people and/or reflecting surfaces. Even
a laser beam of lower intensity may cause eye damage.
Therefore, do not look directly into the laser beam.
● The laser pointer includes no servicing components. Do
not open the housing otherwise the guarantee is void.

Saw blades

● Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the
technical data. Use only the blades specified in this
manual, complying with EN 847-1.