Residual Risks; Safety Of Others - Stanley STCT1860 Manual De Instrucciones

ENGLISH
seek medical help. Liquid ejected from the battery may
cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
ADDITIONAL POWER TOOL SAFETY
WARNING! Additional safety warnings for handheld
saws
♦ Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
♦ Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
♦ Keep hands away from cutting area. Never reach
underneath the work piece any reason. Do not insert
fingers or thumb into the vicinity of the reciprocating blade
and blade clamp. Do not stabilize the saw by gripping the
shoe.
♦ Keep blades sharp. Dull or damaged blades may cause
the saw to swerve or stall under pressure. Always use the
appropriate type of saw blade for the workpiece material
and type of cut.
♦ When cutting pipe or conduit, make sure that they are
free from water, electrical wiring, etc.
♦ Do not touch the workpiece or the blade immediately
after operating the tool. They can become very hot.
♦ Be aware of hidden hazards, before cutting into walls,
floors or ceilings, check for the location of wiring and
pipes.
♦ The blade will continue to move after releasing the
switch. Always switch the tool off and wait for the saw
blade to come to a complete standstill before putting the
tool down.
WARNING! The vibration emission value during actual
use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The vibration
level may increase above the level stated.
♦ The intended use is described in this instruction
manual. The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk
of personal injury and/or damage to property.

RESIDUAL RISKS

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations and
the implementation of safety devices, certain residual risks can
not be avoided. These include:
18
♦ Injuries caused by touching any rotating/moving parts.
♦ Injuries caused when changing any parts, blades or
accessories.
♦ Injuries caused by prolonged use of a tool. When using any
tool for prolonged periods ensure you take regular breaks.
♦ Impairment of hearing.
♦ Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)

SAFETY OF OTHERS

♦ This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
♦ Children should be supervised to ensure that they do not
play with the appliance.
LABELS ON TOOL
The following symbols are shown on the tool along with date
code:
WARNING! To reduce the risk of injury, the user must
read the instruction manual before use.
Wear ear protection.
Wear safety glasses or goggles.
V Volts
A Amperes
Hz Hertz
W Watts
min minutes
Alternating
Current
Position of Date Code (Fig. C)
The Date Code (19), which also includes the year of
manufacture, is printed into the housing.
Example:
Year of manufacturing
Direct Current
n No-Load Speed
0
Class II Construction
Earthing Terminal
Safety Alert Symbol
Revolutions or
/min.
Reciprocation per minute
2018 XX 58