Safety Of Others; Residual Risks - Stanley Fatmax FMCS701 Manual De Instrucciones

Hold power tool by insulated gripping surfaces when
u
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock
Select the correct blade for the material to be cut.
u
Do not operate the machine without the guard in position.
u
Do not operate the machine if the guard does not function
or is not maintained properly.
Ensure that the arm is securely fixed when performing
u
bevel cuts.
Before each cut ensure that the machine is stable.
u
Keep handles dry, clean and free from oil and grease.
u
Keep the surrounding area of the machine well maintained
u
and free of loose materials, e.g. chips and off-cuts.
Ensure the machine and the work area are provided with
u
adequate general or localised lighting.
Do not allow untrained people to operate this machine.
u
Ensure that the blade is mounted correctly before use.
u
Make sure that the blade rotates in the correct direction.
Keep the blade sharp. Follow instruction for lubricating
and changing accessories.
Ensure the speed marked on the saw blade is at least
u
equal to the speed marked on the saw.
Ensure that any spacers and spindle rings used are suit-
u
able for the purpose as stated by Stanley Fat Max.
Repairs to the cut line guidance system should be carried
u
out by authorised repair agents or Stanley Fat Max service
staff.
Remove the battery from the machine before carrying out
u
any maintenance or when changing the blade.
Never perform any cleaning, maintenance, removal of any
u
off-cuts or other parts of the work piece form the cutting
area when the machine is running and the saw head is not
in the rest position.
When possible, always mount the machine to a bench.
u
Make sure all locking knobs and handles are tight before
u
starting any operation.
Never use your saw without the table insert.
u
Never attempt to stop the machine in motion rapidly by
u
jamming a tool or other means against the blade; serious
accidents can be caused unintentionally in this way.
Before using or fitting any accessory consult the instruc-
u
tion manual. The improper use of an accessory can cause
damage.
Raise the blade from the table insert in the work piece
u
prior to releasing the on/of switch.
Do not wedge anything against the fan to hold the motor
u
shaft.
The blade guard on your saw will automatically raise when
u
the arm is brought down; it will lower over the blade when
the arm is raised. The guard can be raised by hand when
(Original instructions)
installing or removing saw blades or for inspection of the
saw. Never raise the blade guard manually unless the
machine is switched off.
Check periodically that the motor air slots are clean and
u
free of chips.
Never make the warning signs on the power tool unrecog-
u
nisable.
Never stand on the power tool. Serious injuries could
u
occur when the power tool tips over or when coming in
contact with the saw blade.
Do not take hold of the saw blade after working before it
u
has cooled. The saw blade becomes very hot while work-
ing.
To avoid injury from materials being thrown, remove the
u
battery from saw to avoid accidental starting, and then
remove small materials.
Before use and after any maintenance the blade guard
u
must be checked to ensure proper function. This test must
be performed with the saw switched off and the battery
removed. The arm must be raised and lowered to ensure
the guard covers the blade and the blade does not contact
the guard. If the guard fails to operate correctly, have your
power tool serviced by a qualified repair agent. Call Stan-
ley Fat Max customer services for you nearest service
agent.
This mitre saw has been designed for sawing wood,
u
plastic and nonferrous metal only. Do not use the saw
to cut other materials than those recommended by the
manufacturer.
Do not take hold of the saw blade after working before it
u
has cooled. The saw blade becomes very hot while work-
@
ing.
Warning! Cutting plastics, sap coated wood,
and other materials may cause melted material
to accumulate on the blade tips and the body of
the saw blade, increasing the risk of the blade
overheating and binding while cutting.

Safety of others

This charger can be used by children aged from 8 years
u
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concern-
ing use of the appliance in a safe way and understand the
hazards involved.
Children shall not play with the appliance. Cleaning and
u
user maintenance shall not be made by children without
supervision.

Residual risks

The following risks are inherent to the use of saws:
Even with the application of the relevant safety regulations
ENGLISH
11