Using The Timer; Usb - Panasonic SC-PM5 Instrucciones De Funcionamiento

Using the timer

Setting the clock Setting the clock
This is a 12-hour clock.
1
Press [CLOCK/TIMER] to select "CLOCK".
Each time you press the button:
2
( Within 5 seconds or so
Press [4/1] or [¡/¢] to set the time.
3
Press [CLOCK/TIMER] again to finish setting the time.
Displaying the clock
Press [CLOCK/TIMER] to display the clock for few seconds.
Note:
Reset the clock regularly to maintain accuracy.
Using the play timer Using the play timer
You can set the timer to come on at a certain time to wake you up.
Preparation
Turn the unit on and set the clock.
Prepare the music source you want to listen to; disc, radio, USB or
music port source, and set the volume.
1
Press [CLOCK/TIMER] repeatedly to select the play timer.
2
( Within 5 seconds or so
Press [4/1] or [¡/¢] to set the time.
3
Press [CLOCK/TIMER] to confi rm.
4
Repeat steps 2 and 3 to set the fi nishing time.
T
o activate the timer
5
Press [˚ PLAY] to turn on the timer.
˚ PLAY
6
Press [y] to turn off the unit.
The unit must be off for the timer to operate.
Change the settings
Change the source
or volume
Cancel
Note:
• The play timer will start at the preset time, with the volume
increasing gradually to the preset level.
• The timer comes on at the set time every day if the timer is on.
• The unit must be in the standby mode for the timer to function.
• If you turn the unit off and on again while a timer is functioning,
the fi nish time setting will not be activated.
Panasonic Corporation
Web Site: http://panasonic.net
RQTX0185-2M_leus.indd 16 RQTX0185-2M_leus.indd 16
CLOCK ˚ PLAY
Original display
)
CLOCK ˚ PLAY
Original display
)
no display (off)
Repeat steps 1 to 4 and 6. (➡ see above)
1) Press [˚ PLAY] to clear the timer
indicator from the display.
2) Make changes to the source or volume.
3) Perform steps 5 and 6. (➡ see above)
Press [˚ PLAY] to clear the timer indicator
from the display.

USB

MP3
The USB connectivity enables you to connect and play MP3 tracks
from USB mass storage class. Typically, USB memory devices.
(Bulk only transfer)
Connecting a USB mass storage device Connecting a USB mass storage device
Preparation
Before connecting any USB mass storage device to the unit, ensure
that the data stored therein has been backed up.
It is not recommended to use a USB extension cable. The device
connected via the cable will not be recognised by this unit.
Playing a USB mass storage device Playing a USB mass storage device
1
Reduce the volume and connect the USB mass storage
device to the USB port.
2
Press [6, USB] or [OK] to start play.
Pause play Press [6, USB].
Press again to resume play.
Press [ 7 ] (stop).
Stop play
"RESUME" is displayed. The position is
memorised.
Press [6, USB] to resume play.
Press [ 7 ] (stop) again to clear the position.
Skip tracks Press [4/1] or [¡/¢].
Press [5 / ∞, ALBUM] in the play mode.
Skip album
Press [5 / ∞, ALBUM] once and then the
numeric buttons in the stop mode.
USB enabled
device
(not included)
Sp En
RQTX0185-2M
L0109CH2050
5/18/10 4:39:48 PM 5/18/10 4:39:48 PM