Replacing The Filters - Black+Decker BHFE520J Manual De Instrucciones

Once the filter housing is removed from the dust
u
canister, use your index finger and thumb to pinch the
filter tabs (17) and rotate the filter (22)
anti-clockwise and remove it as shown in figure L.
Remove the foam filter (23) from the filter housing as
u
shown in figure M.
Shake or lightly brush any loose dust off of the foam
u
filter (23) and filter (22).
Rinse out the dust canister (8) with warm soapy water.
u
Wash the filters with warm soapy water.
u
Ensure the filters are completely dry before refitting the
u
filters into the filter housing (18).
Refit the clean and dry foam filter (23) into the filter
u
housing (18).
Refit the clean and dry filter (23) into the filter (22) by
u
aligning the filter locks (24) , located on the sides
of the filter, with the filter housing slots (25) , located
on the sides of the filter housing, and turn the filter
clockwise until it locks firmly into position as shown in
figure N.
Install the filter housing into the dust canister (8)
u
ensuring the dust canister slots align with the filter housing
tabs as shown in figure N1.
Install the dust canister onto the vacuum, until it "clicks"
u
firmly into position.
Note: Ensure the dust port is placed towards the
main handle (2) of the vacuum and the dust canister
release button (15) is facing away from the vacuum (16).
Removing and cleaning the rotary brushes
(Fig. O, P, Q, R, S)
Warning! To reduce the risk of injury from moving parts,
disconnect the floor brush from the vacuum before cleaning
or servicing.
To remove the rotary brush (26) from the floor head (9)
u
use a coin or straight screwdriver to rotate the lock (27) on
the lock plate (28) to the unlocked position (29) as shown
in figure O.
Remove the lock plate (28).
u
Ease the drive belt (9a) away from the rotary brush (26)
u
The rotary brush (26) can now be removed.
u
Note: The bearings (33) are also removable from the end
pieces (32) allowing you to clear the brushes of any hair or
other debris that may have accumulated as shown in figure Q.
Once the rotary brush has been cleaned, reinstall the
u
rotary brush into the floor head (9) as shown in figure R.
Install the lock plate (28) onto the floor head (9) as shown
u
in figure S.
Use a coin or straight screwdriver to rotate the lock (27)
u
on the lock plate (28) to the locked position (36) as
shown in figure S.
(Original instructions)
Safe storage (Fig. T)
The unit can be safely stored, when not in use, by placing the
catch on the motor unit (6b) onto the storage hook (6a) as
shown in figure T.
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
Run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.

Replacing the filters

The filters should be replaced every 6 to 9 months and when-
ever worn or damaged. Replacement filters are available from
your BLACK+DECKER dealer.
Remove the old filters as described above.
u
Fit the new filters as described above.
u
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
BHFE520J
Voltage
Watt Hours
Weight
ENGLISH
BHFE620J
18V 21.6V
36Wh 43.2Wh
2.02Kg 2.06Kg
9