Using The Dishwasher - Haier QDT125 Serie Manual Del Propietário

USING THE DISHWASHER

Features and appearance will vary throughout this manual
Hold 3 Sec To Cancel
Clean
Sanitized
Start
LOAD DISHWASHER
1
For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of normal food
soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat
trimmings, and excessive amounts of grease or oil.
ADD DETERGENT
2
Add needed amount of detergent to the detergent dispenser. Use detergent such as
Dishwashing Detergent. See Dispensers section.
ADD RINSE AGENT
3
Add rinse agent such as
use of rinse aid can further enhance the dishwasher's drying performance.
SELECT CYCLE
4
Open the door and press the Cycle Select pad for the desired wash cycle. The light next to the Cycle Select pad will be
lit to indicate which wash cycle has been selected.
NOTE: Cycle times vary based on soil level, water temperature, and options selected.
The cycle must be selected with the door in the open position. The cycle will not start until the Start pad is pushed and
the door is closed within 4 seconds.
AutoSense This cycle automatically senses the soil level and adjusts the wash cycle accordingly. It is meant for daily,
regular, or typical use to completely wash a full load of normally soiled dishes and is designed to conserve
both water and energy. NOTE: AutoSense was used to rate the energy efficiency of this dishwasher.
Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.
Everyday dishes are safe to be used in this cycle.
Light This cycle is for lightly soiled dishes. It is safe for china and crystal with no options selected.
SELECT OPTIONS
5
Wash Allows you to select a higher wash temperature. These options are only available for Heavy and
Temp AutoSense cycles. Press the Wash Temp pad until the light next to the desired option comes on.
Boost This option raises the water temperature and extends the cycle time in order to achieve better wash
performance.
Sanitize This option raises the water temperature in the final rinse to sanitize your dishware. The cycle length may vary
depending on the temperature of your inlet water.
NOTE: Cycles using this option are monitored for sanitization requirements. If the cycle is interrupted
during or after the main wash portion or if the incoming water temperature is so low that adequate water
heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the Sanitized
light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle to meet the
requirements of Section 6, NSF 184 for soil removal and sanitization efficacy.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
Delay Start This option allows you to delay the start of a wash cycle for up to 12 hours. With the door open and a
cycle selected, press the Delay Start pad to choose the number of hours you want to delay the start of
the wash cycle. The hours will show in the display window.
NOTE: You may cancel the Delay Start timer by holding the Start pad for 3 seconds. This will also cancel
the wash cycle.
Control You can lock the controls to prevent selections from being made. You can also lock the controls after
Lock you have started a cycle to prevent cycle changes. For example, children cannot accidentally start the
dishwasher by pressing pads with this option selected.
To LOCK/UNLOCK the dishwasher control, press and hold the Cycle Select and Wash Temp pads for 3
seconds. The lock control light ( ) will turn on to indicate the control is locked and will turn off to indicate
the control is unlocked.
49-55125-1
Finish Jet-Dry Rinse Aid
® ®
1-12 hrs
Delay
Start
to the rinse agent dispenser. See Dispensers section.
Hold 3 Sec
Heavy
AutoSense
Light
Cycle Wash
Select Temp
Finish Quantum Automatic
® ®
NOTE: The
Boost
Sanitize
5