Cequent Performance Products 76034 Instrucciones De Instalación página 3

Always wear SAFETY GLASSES
when installing hitch
Scan for step by step
PHOTO installation
instruction or visit
http://www.cequentgro
up.com/qr-product.aspx
Hitch exhaust
hangers (2)
o
STEP 3
Must be install before hitch is
raised into position
(Conical Washer)
Teeth side
against hitch
For vehicles with OEM Tow Hook: Tow hook must be permanently removed for hitch installation.
1. Lower exhaust system at the rubber isolator (3 places). Note: Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal. Remove rubber isolator from mufflers only
(2) to be re-install step 3. Be careful not to allow muffler to fall under its own weight.
2. Remove and return exhaust hanger, and/or exhaust hanger with factory tow hook, and fasteners to vehicle owner.
3. Install carriage bolts (item 6) into exhaust hangers on hitch. Install rubber isolators removed in step 1, onto 7/16 carriage bolts on hitch. Install flat washer, and 7/16-14 hex lock nut. See Figure 3.
4. Feed ½-13 carriage bolt and spacer into passenger side frame rail as shown using reverse pullwire procedure. Leave pullwire attached. See Figure 2.
5. Feed pull wire though hole in bracket on passenger side. Raise hitch into position, over exhaust and align with existing weldnuts in frame rail and ½-13 carriage bolt installed in Step 4. Install M12 hex bolts
and conical washer as shown.
6. Remove pullwire and install conical washer and hex nut on carriage bolt.
7. Tighten all M12 CL.8.8 fasteners with torque wrench to 68 Lb.-Ft (92 N*M) , Tighten all ½-13 GR5 fasteners with torque wrench to75 Lb.-Ft. (102 N*M)
Proper torque is needed to keep the hitch secure to the vehicle when towing.
8 Raise exhaust back into position (3 places). Note: Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. -
Installation Instructions
PART NUMBERS: 76034, 84034
l
m
o
j
o
k
Figure 1
k
Rear
n
Printed in Mexico
Rubber
isolator
Existing weldnuts
Both sides
o
Figure 3
Both sides
j
k
⑨
Sheet 3 of 15
Fastener Kit : 76034F
Hex bolt M12 x 1.75 x
① Qty. (4)
40mm CL8.8
Conical washer
② Qty. (5)
1/2"
Bolt Carriage
③ Qty. (1)
½-13 x 1.50 GR5
Spacer
④ Qty. (1)
¼" x 1.00 x 2.00
Hex nut
⑤ Qty. (1)
p
q
1/2-13
Bolt carriage
⑥ Qty. (2)
7/16-14 x 2.500 GR5
Flat washer
⑦ Qty. (2)
7/16"
Hex lock nut
⑧ Qty. (2)
7/16-14
⑨ Qty. (1) Pull wire
½-13
A. Insert bolt and
B. Align block on
block into frame
access hole
Figure 2
Reverse pull wire procedure
76034NP 4-29-16
C. Pull bolt thru
block
Rev. A