After Use; Maintenance / Service - Skil 0130 Manual Original

• Never use the tool when handle cord is damaged, have it
replaced by a qualified person

AFTER USE

• Store the tool indoors in a dry and locked-up place, out
of reach of children
- store the battery pack separately from the tool
BATTERIES
• The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
• Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
• Do not use the battery when damaged; it should be
replaced
• Do not disassemble the battery
• Do not expose tool/battery to rain
• Permitted ambient temperature (tool/charger/battery):
- when charging 0...+45°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL
4 Read the instruction manual before use
5 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
6 Store tool/charger/battery in locations where temperature
will not exceed 50°C
7 Do not dispose of electric tools and batteries together
with household waste material
8 Beware of sharp blades, after switching off the tool the
blade continues to rotate for a few seconds, switch
off and remove safety key from tool before cleaning/
maintenance.
9 Pay attention to the risk of injury caused by flying
debris (keep bystanders a safe distance away from work
area)
q Wear protective glasses and hearing protection
w Do not expose tool to rain
USE
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Battery level indicator e
- press the battery level indicator button N to show the
current battery level e a
! when the lowest level of the battery indicator
starts flashing after pressing button N e b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button N e c, the battery is not
within the allowable operating temperature range
• Battery protection
The tool is suddenly being switched off or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing button N e c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level e b is shown by the battery level indicator
when pressing button N; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
• Removing/installing the battery r a
- 2 battery packs need to be installed
• Removing/installing safety key M r b
• Adjusting height of tool handle t
Adjusting cutting height (25-75 mm) y
•
- adjust handle F by putting it in slot for desired cutting
height. 1 = 25mm, 2 = 35mm, 3 = 45mm, 4 = 55mm, 5
= 65mm, 6 = 75 mm
• On/off safety switch u
Prevents the tool from being switched on accidentally
- switch on tool by first pressing safety switch A and then
pulling trigger switch B
- switch off tool by releasing trigger switch B
! after switching off the tool the blade continues to
rotate for a few seconds
• Operating instructions
- hold the mower with both hands
- place the mower on the edge of the lawn and mow in a
forward direction
- reverse at the end of each turn, slightly overlapping the
previous cut strip
! only use the mower on dry grass
- keep the mower away from solid objects and plants
! for mowing long grass, first set the cutting
mechanism to the maximum cutting height, then
to a lower cutting height
! adjust your walking pace when mowing long grass
• Grass box full indicator i
- empty grass box H as soon as flap J lowers by itself,
indicating that the grass box is full
- for optimal grass collecting performance regularly clean
the holes underneath flap J with a hand brush

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always switch off the tool, remove battery pack, and
ensure that all moving parts have come to a complete
standstill
• Always keep tool clean
Clean the mower after each use with a hand brush and
•
a soft cloth
! do not use water (especially no high-pressure
sprays)
- remove compacted grass cuttings from the blade area
with a wooden or plastic implement
• Storage o
- for saving substantial storage space fold the tool
handle and store the tool as illustrated; empty grass
box first
! ensure that the handle cord is not trapped when
folding/unfolding the tool handle (do not drop the
handle)
- do not place other objects on top of the mower when
stored
• Regularly check the grass box for wear or damage
• Regularly check for worn or damaged blades and bolts
and have them replaced in sets to preserve balance
12