Senco PC1286EU Instrucciones De Operación página 4

● HANDLE COMPRESSOR CORRECTLY
Operate the compressor according to the instructions
provided herein. Never allow the compressor to be
operated by children, individuals unfamiliar with its
operation or unauthorized personnel.
● KEEP ALL SCREWS, BOLTS AND COVERS TIGHTLY IN
PLACE
Keep all screws, bolts, and plates tightly mounted. Check
their conditions periodically.
● KEEP MOTOR AIR VENT CLEAN
The motor air vent must be kept clean so that air can
freely flow at all times. Check for dust build-up frequently.
● OPERATE COMPRESSOR AT THE RATED VOLTAGE
Operated the compressor at voltages specified on their
nameplates. If using the compressor at a higher voltage
than the rated voltage, it will result in abnormally fast
motor revolution and may damage the unit and burn
out the motor.
● NEVER USE COMPRESSOR WHICH IS DEFECTIVE OR
OPERATING ABNORMALLY
If the compressor appears to be operating unusually,
making strange noises, or otherwise appears defective,
stop using it immediately and arrange for repairs by
an authorized service center.
● DO NOT WIPE PLASTIC PARTS WITH SOLVENT
Solvent such as gasoline, thinner, benzine, carbon
tetrachloride, and alcohol may damage and crack plastic
parts. Do not wipe them with such solvents. Wipe plastic
parts with a soft cloth lightly dampened with soapy water
and dry thoroughly.
● USE ONLY GENUINE REPLACEMENT PARTS
Replacement parts not original may void your warranty
and can lead to malfunction and resulting injuries.
Genuine parts are available from your dealer.
● DO NOT MODIFY THE COMPRESSOR
Do not modify the compressor. Always contact the
authorized service center any repairs. Unauthorized
modification may not only impair the compressor
performance but may also result in accident or injury to
repair personnel who do not have the required knowledge
and technical expertise to perform the repair operations
correctly.
● TURN OFF THE SWITCH WHEN THE COMPRESSOR
IS NOT USED
When the compressor is not used, turn the switch OFF,
disconnect the plug from the power source and open
the drain cock to discharger the compressor air from the
air tank.
● NEVER TOUCH THE SURFACE OF THE HIGH-
TEMPERATURE SECTION
In order to prevent a burn, do not touch the piping,
head, cylinder, motor and inverter case (lower cover).
● DO NOT DIRECT AIR STREAM AT BODY
Risk of injury, do not direct air stream at persons or
animals.
● DRAIN TANK
Drain tank daily or after 4 hours of use. Open drain fitting
and tilt compressor to empty accumulated water.
4
● DO NOT STOP COMPRESSOR BY PULLING OUT
THE PLUG
Use the "ON/OFF"switch.
● REPLACEMENT PARTS
When servicing, use only Manufacturer genuine parts.
Repair should be conducted only by authorized service
center.
● NEVER USE A TRANSFORMER
● NEVER CONNECT THE COMPRESSOR TO AN ENGINE
GENERATOR OR DIRECT-CURRENT POWER SUPPLY
The compressor will break or be damaged from burning.
● DO NOT INSTALL THE COMPRESSOR IN ANY PLACE
EXPOSED TO RAIN OR SPLASHED WATER, HIGH-
HUMIDITY PLACE OR HIGH-TEMPERATURE PLACE
If used in the wet condition, it could produce an electric
shock or be short-circuited, resulting in ignition. Use it
under the environmental conditions provided by its
specifications.
● BE SURE TO EARTH THE COMPRESSOR
Earth the compressor to prevent a worker from getting
an electric shock. It comes with a 3-pole cord and a
3-pole earthing plug so that it can be connected to an
appropriate earthing plug socket. A green-and-yellow
striped wire is an earthing conductor. Never connect it to
other charged terminals.
Tab.1 SECTION VALID FOR A MAX
LENGTH OF 65' (20M)
COMPRESSOR HP
PC1286EU 2
WARNING
Avoid electrical shock hazard. Never use this compressor
with a damaged or frayed electrical cord or extension cord.
Inspect all electrical cords regularly. Never use in near wa-
teror in any environment where electric shock is possible.
kW 220/230V 110/120V
1.5 1.5(mm ) 12AWG
2