Descargar Imprimir esta página

GM 23266300 Instrucciones De Montaje

Cadillac xt5 2017-2022

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Accessory Splash Guard Front Kit
Please read instructions thoroughly before starting.
Installation time: 30 minutes.
Package Contents:
Description
Left Hand Splash Guard
Right Hand Splash Guard
M4.2 Screw
M4.2 U-Nut
Washer
Alcohol Wipes
Instruction Sheet
Tools Required:
3/16" (5mm) Drill Bit/Drill
T15 TORX Driver
Clean Cloth/Rag
Installation Procedure:
1.
Clean and degrease body panel where splash guards are to be
located.
2.
Using alcohol wipes or 50% alcohol and water, clean area to be
taped.
3.
Parts and vehicle temperature must be between 61°F & 86°F
(16°C & 31°C).
4.
Remove existing torx head screw location B, discard screw.
See Figure 1.
5.
Mount splash guard and install supplied screw and washer in
location B while holding part up and into front panel and tighten.
See Figure 1.
6.
as a template, drill 3/16" (5mm) holes in locations A and C. See
Figure 1.
7.
Remove supplied screw and washer location B then
splashguard. Pull liner out at location A and install supplied
M4.2 U-Nut over plastic panel brace drilled hole with turned up
edge facing inside of panel. See Figure 1&2.
8.
Install supplied M4.2 U-Nut over drilled hole location C with
turned up edge facing inside of panel. See Figure 3.
9.
Ensure tape liner is facing outward then mount splash guard
and reinstall supplied screw and washer in location B while
holding part up and into front panel. See Figure 1.
NOTE: WHEN TIGHTENING SCREW MAKE SURE WASHER
IS CENTERED
10. While holding splash guard up into panel install supplied M4.2
screw and washer in location A and C and tighten. See Figure
1, 2 & 3.
11. Push splash guard forward and pull tape liner off, while holding
pressure along tape length to ensure contact. See Figure 1.
12. Repeat procedure for other side.
13. Guards can be cleaned with any commercially available
cleaner.
Accessory Splash Guard Front Kit
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
17JN15
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE
WITH GM SPECIFICATIONS.
Quantity
1
1
6
4
6
2
1
REVISION
Initial Release - Vinay Saini
FIGURE 1
SUPPLIED
M4.2 SCREW
SUPPLIED
WASHER
SUPPLIED
WASHER
EXISTING
M4.2 SCREW
SUPPIED
WASHER
NOTE: MAX TORQUE ON M4.2 SCREW IS 3.0NM
FIGURE 2
OUTER
PANEL
SPLASHGUARD
SUPPLIED
WASHER
NOTE: INSTALL SUPPLIED U-NUT WITH TURNED UP
EDGE ON INSIDE OF PANEL.
FIGURE 3
LINER
SPLASHGUARD
NOTE: INSTALL SUPPLIED U-NUT WITH TURNED UP
EDGE ON INSIDE OF PANEL.
PART NO.
IR 17JN15
INSTALLATION INSTRUCTIONS
AUTH
DR
TITLE
N/A
Accessory Splash Guard Front Kit
PART NO.
23266300
SUPPLIED
TAPE
M4.2 U-NUTS
LINER
SPLASHGUARD
SUPPLIED
M4.2 SCREW
BRACE
SUPPLIED
M4.2 U-NUT
LINER
SUPPLIED M4.2
SCREW
SUPPLIED
M4.2 U-NUT
OUTER
PANEL
SUPPLIED M4.2
SCREW
23266300
SHEET
SHEET
A
B
C
SUPPLIED
WASHER
1
3
OF
1
3
OF

Publicidad

loading

Resumen de contenidos para GM 23266300

  • Página 1 EXACTLY AS SHOWN ON 8.5 x 11 17JN15 Initial Release - Vinay Saini Accessory Splash Guard Front Kit WHITE 16 POUND NON-BOND RECYCLABLE PAPER. PRINT ON BOTH SIDES, EXCLUD- ING TEMPLATES. PART NO. 23266300 TO BE UNITIZED IN ACCORDANCE SHEET WITH GM SPECIFICATIONS.
  • Página 2 EXACTLY AS SHOWN ON 8.5 x 11 17JN15 Initial Release - Vinay Saini Accessory Splash Guard Front Kit WHITE 16 POUND NON-BOND RECYCLABLE PAPER. PRINT ON BOTH SIDES, EXCLUD- ING TEMPLATES. PART NO. 23266300 TO BE UNITIZED IN ACCORDANCE SHEET WITH GM SPECIFICATIONS.
  • Página 3 EXACTLY AS SHOWN ON 8.5 x 11 17JN15 Initial Release - Vinay Saini Accessory Splash Guard Front Kit WHITE 16 POUND NON-BOND RECYCLABLE PAPER. PRINT ON BOTH SIDES, EXCLUD- ING TEMPLATES. PART NO. 23266300 TO BE UNITIZED IN ACCORDANCE SHEET WITH GM SPECIFICATIONS.