GM 23425867 Instrucciones De Montaje

Camaro "RALLY" Decal
V6 COUPE KIT CONTENTS
Description
1 Decal - Hood LH (V6)
2 Decal - Hood RH (V6)
3 Decal - R/Cmpt Lid (CPE)
4 Decal - Spoiler (D80 "Base" Spoiler only)
5 Decal - Spoiler (for use on the SB3 Accessory
spoiler or the ZL1 D52 spoiler)
V6 CONVERTIBLE KIT CONTENTS
Description
1 Decal - Hood LH (V6)
2 Decal - Hood RH (V6)
6 Decal - R/Cmpt Lid (CONV)
4 Decal - Spoiler (D80 "Base" Spoiler only)
V8 COUPE KIT CONTENTS
Description
7 Decal - Frt Fascia
8 Decal - Hood LH (V8)
9 Decal - Hood RH (V8)
3 Decal - R/Cmpt Lid (CPE)
4 Decal - Spoiler (D80 "Base" Spoiler only)
5 Decal - Spoiler (if necessary, for use on the SB3
Accessory spoiler or the ZL1 D52 spoiler)
V8 CONVERTIBLE KIT CONTENTS
Description
7 Decal - Frt Fascia
8 Decal - Hood LH (V8)
9 Decal - Hood RH (V8)
6 Decal - R/Cmpt Lid (CONV)
4 Decal - Spoiler (D80 "Base" Spoiler only)
Decal-Spoiler
Decal-Spoiler
(D52 & SB3)
(D80)
Decal-Spoiler
(D80)
Decal-Spoiler Decal-Spoiler
(D80)
(D52 & SB3)
RALLY Stripes
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE
WITH GM SPECIFICATIONS.
Quantity
1
1
1
1
Quantity
1
1
1
1
Quantity
1
1
1
1
1
1
Quantity
1
1
1
1
1
Decal-R/Cmpt Lid
Decal-Hood
(Coupe)
Kit Contents
Decal-Hood
LH
Decal-R/Cmpt Lid
(Conv)
Decal-Hood
RH
Kit Contents
Decal-Hood
Decal-R/Cmpt Lid
(Coupe)
Decal-Hood
Kit Contents
REVISION
Decal-Spoiler
(D80)
TOOLS REQUIRED
Pen / Marker
Measuring Tape
Heat Gun / Hair Dryer
Scissors
Plastic squeegee
Masking tape
IPA
To ensure a bubble free application, put 3 tiny drops of liquid dish soap into a trigger type plastic spray bottle. Set nozzle
IRU ¿QH PLVW 
LH
Processing Instructions:
1. The paint surface where the decals are to be applied must be thoroughly
washed with a warm soap and water solution.
2. If present, heavy contamination like tar should be removed with Prepsol or
other quality solvent.
Decal-Hood
RH
3. Wipe the paint surface with Isopropyl Alcohol just before starting the
application. Follow with a dry wipe.
Coupe 4. Vehicle body surface and part must be 21°C or higher.
5. Use the Soap / Water mixture to thoroughly saturate the paint surface where
the decal is to be applied.
6. Position and install the decals per the instructions on pages 1-4.
7. 7KRURXJKO\ VTXHHJHH WKH HQWLUH VXUIDFH ZLWK ¿UP RYHUODSSLQJ VWURNHV
8. Remove the premask by pulling it off at 180° or parallel to the surface.
9. If the decal tends to lift off the paint as the premask is being removed, the
cause is:
a. Too much soap in the spray bottle. Rinse it out and use less soap.
b. 1RW HQRXJK SUHVVXUH RQ WKH ¿OP VXUIDFH IURP WKH VTXHHJHH ,QFUHDVH
pressure and insure overlapping strokes.
10. For any areas that may be lifting, reapply soap solution to the decal, wrap a
Convertible
towel around the squeegee and resqueegee.
11. For a bubble removal, use a needle or a pin to carefully pierce the bubble to
release the trapped water.
12. Maintain vehicle body temperature of 21ºC or higher for a minimum of 30
mins after stripe installation.
Decal Front
LH Fascia
V6 Hood Decal Installation
1. Use scissors to trim out the hood template and tape into place.
2. /D\ WKH /+ GHFDO XSVLGH GRZQ RQ D ÀDW VXUIDFH DQG JHQWO\ GHWDFK DQG
remove the release liner from the decal.
3. Spray a generous amount of surfactant onto the exposed decal adhesive
and the vehicle surface.
RH
4. Position the decal into place on the hood, aligning the side of the rear
edge to the template, the rear to the panel edge and the inner front edge
Coupe
1/4" from the center line of the hood.
IR 21FE14
INSTALLATION INSTRUCTIONS
AUTH DR
TITLE
PART NO.
Decal-R/Cmpt Lid
(Conv)
Needle or Pin
Isopropyl alcohol
Clean towels
Liquid dish soap
Water
Trigger-type spray bottle
Unscented
Dishwashing
Liquid
23432805
PART NO.
RALLY Stripes
23432805
SHEET
Decal Front
Decal-Hood
Fascia
LH
Decal-Hood
RH
Kit Contents Convertible
Water
1 14
SHEET OF
1 14
OF