Recharging The Battery; Appliance Safety; Preparing To Work; Work - Fimap FV9+ B Manual De Uso Y Mantenimiento

RECHARGING THE BATTERY

The battery must be charged prior to the first use, and when it doesn't provide enough power for tasks
that could formerly be performed without difficulty. To recharge the battery, proceed as follows:
1. Take the appliance to the dedicated battery recharging area.
2. If the appliance is working, turn it off using the main switch (1) (Fig.1).
3. To remove the power battery (2) from the appliance, you must first free it by shifting the stop levers
(3) in the direction of the two arrows (Fig. 2). Remove the battery by lifting it out of the appliance.
4. Connect the plug (4) on the battery charger power cable to the socket (5) in the base of the charger
(Fig.3).
1
3
2
1
5. Connect the battery charger power supply cable plug to the mains socket.
WARNING: Before connecting to the plug to the socket, check that the characteristics of the
mains power supply corresponds to that of the battery charger.
6. Place the main switch (6), on the base of the battery charger, to position "I" (Fig.4).
N.B. : Make sure the green LED (7) on the battery charger lights up when you enable the battery
charger base circuit (Fig.5). This LED indicates that the battery charger circuit is correctly
powered.
WARNING: Before inserting the battery into the charging holder, check that there is no
condensation or other liquid in the dock that will hold the battery.
7. Insert the battery (2) in the seat (8) in the battery charger, taking care to position the poles (9) in the
battery correctly (Fig. 6).
6 7
4
N.B.: The battery can only be inserted into the charger one way. Do not use force when inserting
the battery.
WARNING: Carefully read the battery charger use and maintenance manual delivered with the
appliance, before charging the battery.
N.B. : Check that, when inserting the battery into the base of the battery charger, the red LED (10)
present on the battery charger(Fig.7) turns on. This LED indicates that the battery is recharging.
8. Perform a complete battery charging cycle.
N.B. : the red LED (10) remains on until the battery is fully charged.
N.B. : The charger and the battery can be left connected to the power outlet. The red LED (10)
lights up when the charger occasionally tops up the battery.
N.B.: the red charge status LED (10) does not provide any indication of the battery charge level.
N.B. : The battery may overheat during the charging phase, nevertheless, this is normal and does
not imply that there is a problem with the battery.
ATTENTION: If the battery used in this device is over-charged, this may present a risk of fire,
explosion or chemical burns.
9. With charging complete, position the main switch (6), on the base of the battery charger, to position
"0" (Fig.8).
10. Disconnect the battery charger power supply cable plug from the mains socket.
WARNING: To prevent damaging the power cable, disconnect the plug from the mains socket by
directly pulling the plug and not the cable.
11. Remove the battery (2) from the base of the charger (8) pulling it out (Fig.9).
10
7
10071876-AA_UM_FV9+ B.indb 18
5
4
2 3
2
9
8
5 6
2
6
8
8 9

APPLIANCE SAFETY

1. Switch off the appliance by positioning the main switch (1) to "0" (Fig.1).
2. To remove the power battery (2) from the appliance, you must first free it by shifting the stop levers
(3) in the direction of the two arrows (Fig. 2). Remove the battery by lifting it out of the appliance.
1 3
2
1 2

PREPARING TO WORK

1. Remove the cover (1) from the vacuum tank (Fig.1), using the hooks (2) on the side of the tank
itself (Fig.2).
2. Check the fabric filter (3) is correctly positioned (Fig. 3)and that the collection bag (4) is correctly
inserted inside it (Fig. 4).
1
2
1 2
3. Fasten the cover (1) above the vacuum tank (Fig.5), locking it with the hooks (2) on the side of the
tank itself (Fig.6).
1
4
4 5
4. Insert the nozzle (5) on the vacuum hose into the hole on the cover of the vacuum tank (Fig.7).
5. Connect the handle (6) on the vacuum hose with the telescopic tube (7) (Fig.8).
6. Select the most suitable accessory for the work to be carried out. Connect the accessory (8) with the
telescopic tube (7) (Fig.9).
7. Insert the battery (9) in the battery compartment on the top of the appliance, making sure that the
poles of the battery are facing the top of the appliance. Press the battery until the clamp (10) is in
place (Fig.10).
6
5
7
7 8
10
9
10
1. Switch on the machine by setting the main switch (1) to "I" (Fig. 1).
2. If you are using the combined brush, set the switch (2) on the brush body to "HARD SURFACE" or
"CARPET" depending on the floor to be cleaned (Fig.2).
3. Proceed with the vacuuming.
N.B. : If the vacuuming capacity is excessive, shift the lever (3) on the vacuum hose handle (Fig.
3)while the accessory is in contact with the floor.
N.B. : On the front of the appliance there are 4 different colour LED, one red and three green,
which signal the battery charge level (Fig.4). When only the red is lit the battery is at a critical
level, switch off the appliance and charge the battery (read the chapter
BATTERY").
1
1 2
4
18
3
3
2
6
9

WORK

"CHARGE THE
2
3
7
8
3
19/01/18 14:20