DeWalt DW702 Manual De Instrucciones página 30

E N G L I S H
- Right side
• Position the moulding with the bottom of the moulding against the fence.
• Save the left side of the cut.
Outside corner
- Left side
• Position the moulding with the bottom of the moulding against the fence.
• Save the right side of the cut.
- Right side
• Position the moulding with top of the moulding against the fence.
• Save the right side of the cut.
Cutting crown mouldings
The cutting of crown moulding is performed in a compound mitre. In order
to achieve extreme accuracy, your saw has pre-set angle positions at
31.62° mitre and 33.85° bevel. These settings are for standard crown
mouldings with 52° angles at the top and 38° angles at the bottom.
• Make test cuts using scrap material before doing the final cuts.
• All cuts are made in a left bevel and with the back of the moulding
against the base.
Inside corner
- Left side
• Top of the moulding against the fence.
• Mitre right.
• Save the left side of the cut.
- Right side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
Outside corner
- Left side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
- Right side
• Top of the moulding against the fence.
• Mitre right.
• Save the right side of the cut.
Dust extraction (fig. A2 & A6)
• Fit the dustbag (32) onto the dust spout (20).
• Whenever possible, connect a dust extraction device designed in
accordance with the relevant regulations regarding dust emission.
Saw blades
To obtain the stated cutting capacities, always use 250 mm saw blades
with 30 mm arbor holes.
Consult your dealer for further information on the appropriate accessories.
Transporting (fig. B)
In order to conveniently carry the mitre saw, a carrying handle (9) has been
included on the top of the saw arm.
• To transport the saw, lower the arm and depress the lock down pin (18).
• Always use the carrying handle (9) or the hand indentations (22) shown
in fig. B to transport the saw.
en - 7
Maintenance
Your D WALT Power Tool has been designed to operate over a long
E
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Cleaning
Keep the ventilation slots clear and regularly clean the housing with a soft
cloth.
• Regularly clean the table top.
• Regularly clean the dust collection system.
Unwanted tools and the environment
Take your tool to an authorized D
disposed of in an environmentally safe way.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your
D WALT machine, simply return it within 30 days, complete as
E
purchased, to the point of purchase, for a full refund or exchange.
Proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your D
12 months following purchase, it will be undertaken free of charge at
an authorized D WALT repair agent. Proof of purchase must be
E
produced. Includes labour and spare parts for Power Tools.
Excludes accessories.
• ONE YEAR WARRANTY •
If your D WALT product becomes defective due to faulty materials or
E
workmanship within 12 months from the date of purchase, we
guarantee to replace all defective parts free of charge or, at our
discretion, replace the unit free of charge provided that:
• The product has not been misused.
• Repairs have not been attempted by unauthorized persons.
• Proof of purchase date is produced.
This guarantee is offered as an extra benefit and is additional to
consumers statutory rights.
For the location of your nearest authorized D
please use the appropriate telephone number on the back of this
manual. Alternatively, a list of authorized D
details on our after-sales service are available on the Internet at
www.2helpU.com.
WALT repair agent where it will be
E
GUARANTEE
WALT machine, in the
E
WALT repair agent,
E
WALT repair agents and full
E
22