Package Contents; Electrical Safety - DeWalt DW711 Manual De Instrucciones

• Replace the kerf plate when worn.
• Disconnect the machine from the mains before carrying out any
maintenance work or when changing the blade.
• Never perform any cleaning or maintenance work when the machine is
still running and the head is not in the rest position.
• When possible, always mount the machine to a bench.
Additional safety rules for saw benches
• Make sure that the blade rotates in the correct direction and that the
teeth are pointing to the front of the saw bench.
• Be sure all clamp handles are tight before starting any operation.
• Be sure all blade and flanges are clean and the recessed sides of the
collar are against the blade. Tighten the arbor nut securely.
• Keep the saw blade sharp and properly set.
• Make sure that the riving knife is adjusted to the correct distance from
the blade - maximum 5 mm.
• Never operate the saw without the upper and lower guards in place.
• Keep your hands out of the path of the saw blade.
• Disconnect the saw from the mains supply before changing blades or
carrying out maintenance.
• Use a push stick at all times, and ensure that you do not place hands
closer than 150 mm from the saw blade while cutting.
• Do not attempt to operate on anything but the designated voltage.
• Do not apply lubricants to the blade when it is running.
• Do not reach around behind the saw blade.
• Do not use the saw for cutting any material other than wood.
• Take care when slotting.
Residual risks
The following risks are inherent to the use of saws:
- injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw
blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
Labels on tool
The following pictograms are shown on the tool:
Read the instruction manual before use
When using the machine in the mitre saw mode, make sure
that the upper part of the saw blade is fully covered by the
upper saw blade guard. Only use the machine when the bench
saw table is in highest position.
When using the machine in the bench saw mode, make sure
that the upper and lower guards are in place. Only use the
machine when the bench saw table is in horizontal position.

Package contents

The package contains:
1 Assembled table top mitre saw
1 Parallel rip fence
1 Guard for bench saw position
1 Bottom guard for bench saw position
1 Push stick
1 Allen key 4/6 mm
1 Allen key 5 mm
1 Two-pin spanner
1 Dust extraction adapter for top guard
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
• Remove the saw from the packaging material carefully.
• Release the head lock down knob to raise the head of the machine.
Description (fig. A1 - A5)
Your DW711 table top mitre saw has been developed for professional
applications. This high precision machine can be easily and quickly set to
crosscut, bevel, mitre, or compound mitre.
A1
1 On/off switch
2 Head lock up release lever
3 Additional saw bench table locking knob
4 Moveable lower blade guard
5 Fixed table
6 Blade slot
7 Mitre lever
8 Mitre latch
9 Rotating table/mitre arm
10 Mitre scale
11 Fence
12 Bevel clamp handle
13 Head lock down knob
A2
14 Saw bench table
15 Riving knife
16 Upper saw blade guard
17 Rip fence
18 Fixed lower guard (for use in bench saw position)
19 Attachment mounting holes
Optional accessories
A3
20 Table end plate
21 Support guide rails
22 Material support plate
23 Material clamp
24 Swivelling stop
25 Adjustable stand 760 mm (max. height)
26 Legstand
A4
27 Length stop for short workpieces (to be used with guide rails [21])
A5
28 Legstand
29 Roller table

Electrical safety

The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
B&D_19a
E N G L I S H
25