Basic Operation - AEG VCR 4505 Manual De Instrucciones

HG210ED(EN).fm Page 8 Tuesday, March 2, 2004 4:08 PM
Channel Reprogramming
You can replace two channels.
• Use the remote control for this procedure.
1) Press .
MENU
2) Press / or /
PLAY o STOP L
/ .
F.FWD B
3) Press / or /
PLAY o STOP L
press / .
F.FWD B
4) Press
/ or /
PLAY o STOP L
then press / .
F.FWD B
5) Press
/ or /
PLAY o STOP L
number you want to change the channel, then press
/ .
F.FWD B
•You cannot select a position number where "- - -"
appears next to the number. This is because SKIP is set
to [ON] for this position number.
•When a weak signal is received in Channel
Reprogramming mode, you can change the background
to static blue by pressing
If you press the button again, the background will return
to the static screen.
6) Press
/ or /
PLAY STOP
o L
move to another position number, then press

Basic Operation

Playback
Tracking Adjustment
• Tracking adjustment will be activated automatically
(Digital Tracking function) when you start playback.
• When playing pre-recorded tapes or tapes recorded on units
other than your own, noise lines (black and white streaks)
may appear on the playback picture. If this occurs, you can
adjust the tracking control manually by pressing
( / ) until the streaks disappear. To return to
CHANNEL
o p
the DTR function, stop the tape once and start playback
again.
1) Turn on the TV and select the video channel on the TV.
2) Insert a prerecorded tape.
The VCR will turn on automatically. If the erase-
protection tab has been removed, the VCR will start
playback automatically.
3) Press
/ to begin playback.
PLAY
o
•Tracking adjustment will be activated automatically
(Digital Tracking function) when you start playback. To
adjust the tracking manually, press
<If a tape is already in the VCR...>
•Using the buttons on the VCR
Just press on the VCR. Power will automatically
PLAY
turn on and playback will start. (Direct Button
Operation)
•Using the buttons on the remote control
Press to turn on, and then press
FUNCTION
4) Press / to stop playback.
STOP
L
to select "INITIAL", then press
to select "CH TUNING", then
repeatedly to select "MOVE",
repeatedly to select the position
.
TAPE COUNTER RESET
repeatedly until the channel
/ .
F.FWD
B
( / ).
CHANNEL
o p
.
/
PLAY
o
7) Press .
MENU
MENU
TIMER
SET UP
INITIAL
MOVE
P01: 02 P06: 07
P02: 03 P07: 08
[ ]
P03: 04 P08: 09
P04: 05 P09: 10
P05: 06 P10: 11
Position
Channel
Number
Number
MOVE
P01: 02 P06: 07
P02: 03 P07: 08
P03: 11 P08: 09
P04: 05 P09: 10
[ ]
P05: 06 P10: 04
Speed Search
1) Press / or /
F.FWD B REW s
videotape at a high speed in either a forward or reverse
direction. In this mode, the sound will be muted.
2) Press the button again, the VCR will now search in super
high speed. (This function will not operate for a NTSC
tape.)
3) Press
/ to return to normal playback.
PLAY o
Still Picture
Press during playback to view a still picture on
PAUSE/STILL
the TV screen.
• If you press to freeze the picture, usually
PAUSE/STILL
there will be noiselines on the TV screen. This is normal,
however, each time you press
change position.
• When the picture begins to vibrate vertically, stabilize the
picture by pressing
CHANNEL
• After the VCR has been in Still mode for 5 minutes, it will
stop automatically to protect the tape and the video head.
<Note for "Speed Search" and "Still Picture">
• Usually there will be video "noise" lines (black and white
streaks or dots) on the screen. This is normal.
The still picture will, in addition to containing the "noise"
lines, be black and white.
This is not a fault of the machine but merely a by-product
of the technology involved in producing a VCR with
LP mode.
8
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
MOVE
P01: 02 P06: 07
P02: 03 P07: 08
P03: 11 P08: 09
P04: 05 P09: 10
P05: 06 P10: 04
during playback to view a
the lines will
PAUSE/STILL
( / ) in the Still mode.
o p
EN