Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
triple-core extension cable suitable for the power
input of this tool (see technical data). The minimum
conductor size is 1.5 mm
always unwind the cable completely. Also refer to
the table below.
2
Conductor size (mm
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Selecting the operating mode (fig. B)
The Rotary Hammer Drill can be used in three
operating modes:
Rotary drilling:
for screwdriving, drilling into steel, wood
and plastics
17
2
. When using a cable reel,
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
.
• Select the required operating mode by rotating
the mode selector (4) towards the symbol on the
gear housing.
• For screwdriving, refer to section "Instructions for
use".
Inserting and removing SDS-plus
(fig. C)
Your Rotary Hammer Drill uses SDS-plus
(refer to the inset in fig. C for a cross-section of an
®
SDS-plus
bit shank).
• Clean and grease the bit shank.
• Insert the bit shank into the tool holder (8).
• Push the bit down and turn it slightly until it fits
60
into the slots.
• Pull on the bit to check if it is properly locked.
6
10
The hammering function requires the bit to be
15
able to move axially several centimetres when
20
locked in the tool holder.
-
-
-
• To remove a bit pull back the tool holder locking
6
6
sleeve (9) and pull out the bit.
6
6
Fitting the side handle (fig. D)
15
15
The side handle (5) can be fitted to suit both RH-
and LH-users.
20
-
• Loosen the side handle.
• For RH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the left.
• For LH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
• Insert the required drill bit.
• Slacken the side handle (5).
Hammer drilling:
simultaneous rotating and impacting for
concrete and masonry drilling and
carbide tipped core drilling
Hammering only with spindle lock:
impacting only - for light chipping,
chiselling and demolition applications.
Always use the tool with the side handle
properly assembled.
E N G L I S H
®
accessories
®
accessories
en - 4
Publicidad
Tabla de contenido
