Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
. When using a cable reel,
always unwind the cable completely.
Also refer to the table below.
2
Conductor size (mm
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Inserting and removing SDS-plus® accessories
(fig. B)
Your rotary hammer uses SDS-plus® accessories
(refer to the inset in fig. B for a cross-section of an
SDS-plus® bit shank).
• Clean and grease the bit shank.
• Insert the bit shank into the tool holder (6).
• Push the bit down and turn it slightly until it fits
into the slots.
• Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
15
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• To remove a bit pull back the tool holder locking
sleeve (7) and pull out the bit.
Fitting the side handle (fig. C)
The side handle (3) can be fitted to suit both
RH- and LH-users.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the left.
• For LH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
60
Setting the drilling depth (fig. D)
6
10
• Insert the required drill bit.
15
• Slacken the side handle (3).
20
• Fit the depth adjustment rod (4) through the hole
25
in the side handle clamp.
-
• Adjust the drilling depth as shown.
-
-
• Tighten the side handle.
6
6
6
6
Replacing the dust cover (fig. B)
15
The dust cover (5) prevents dust ingress into the
15
mechanism. Replace a worn dust cover
20
immediately.
-
• Pull back the tool holder locking sleeve (7) and
pull the dust cover (5) off.
• Fit the new dust cover.
• Release the tool holder locking sleeve.
Instructions for use
• Always observe the safety instructions
Be aware of the location of pipework and wiring.
Apply only a gentle pressure to the tool (approx. 5 kg).
Excessive force does not speed up drilling but
decreases tool performance and may shorten tool life.
Do not drill too deep to prevent damage to the dust
cover.
Always use the tool with the side handle
properly assembled.
and applicable regulations.
E N G L I S H
en - 4
Publicidad
Capítulos
Tabla de contenido
