Stanley FATMAX SFMCN616 Manual Del Usuario página 10

ENGLISH
Preparing the tool
Warning! NEVER spray or in any other way apply oil,
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Read the Safety Instruction section of this manual.
u
Wear eye and ear protection.
u
Remove battery from tool and fully charge.
u
Ensure magazine is empty of all fasteners.
u
Check for smooth and proper operation of contact trip and
u
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
Keep tool pointed away from yourself and others.
u
Insert fully charged battery pack.
u
Loading the Tool (Fig. F)
Warning! Keep the tool pointed away from yourself and
others. Serious personal injury may result.
!
Warning Never load nails with the contact trip or
trigger activated.
!
Warning Always remove battery pack before loading or
unloading nails.
!
Warning
The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
!
Warning
Keep fingers clear of pusher to prevent injury.
Insert fasteners into the bottom of the magazine (9).
u
Pull pusher latch (10) downward until the nail follower (16)
u
falls behind the nails as shown in figure F.
Release the pusher latch(10).
u
Unloading the Tool
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Press pusher latch release button (11).
u
Manually slide nails towards the bottom of the
u
magazine (9).
Open the jam clear door on the nosepiece to verify there
u
are no nails remaining.
Adjusting Depth (Fig. G)
The depth that the fastener is driven can be adjusted using
the depth adjustment wheel (3) on the side of the tool.
Warning!To reduce risk of serious injury from accidental
actuation when attempting to adjust depth, Always:
Remove battery pack.
u
Engage trigger lock-off.
u
Avoid contact with trigger during adjustments.
u
10
(Original instructions)
Depth settings are on a sliding scale on the depth adjustment
indicator (4). The left side indicating the deepest and the right
side indicating the shallowest.
To drive a nail deeper, rotate the depth adjustment
u
wheel (3) downwards. This will slide the depth adjustment
indicator (4) to the left on the scale.
To drive a nail shallower, rotate the depth adjustment
u
wheel (3) upwards. This will slide the depth adjustment
indicator (4) to the right on the scale.
Work lights (Fig. H)
There are work lights (5) located on each side of the nailer.
Work lights turn on upon depressing the contact trip.
Note: These work lights are for illuminating the immediate
work surface and are not intended to be used as flashlights.
Low Battery Indicator
The work lights will flash and then turn off completely to
indicate low battery.
Jammed Nail Indicator
The work lights will flash continually if a nail becomes jammed
in the nose piece (see Clearing a jammed nail).
Stall Release (Fig. I)
Warning! If a stall occurs, the tool will disable itself and
will require you to reset it. To do so, follow instructions on
clearing a stalled condition. Next remove battery pack and
then reinsert battery pack. The tool will now be operational. If
the nailer is used in a rigorous application where all available
energy in the motor is used to drive a fastener, the tool may
stall. The driver blade did not complete the drive cycle and the
jam/stall indicator will flash. Rotate the stall release lever (6)
on the tool and the mechanism will release.
Note! The tool will disable itself and not reset until the battery
pack has been removed and reinserted. If the unit continues
to stall please review the material and fastener length to be
sure that it is not too rigorous an application. If the driver
blade does not automatically return to the home position
after rotating the stall release lever, proceed to "clearing a
jammed nail".