Stanley FATMAX SFMCN616 Manual Del Usuario página 9

Hot/Cold Pack Delay
When the charger detects a battery that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, the green
LED (13a) will flash intermittently, while the red LED (13b)
will remain on continuously, suspending charging until the
battery has reached an appropriate temperature. The charger
then automatically switches to the pack charging mode. This
feature ensures maximum battery life.
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in figure B. By
pressing the state of charge button (12a) you can easily view
the charge remaining in the battery as illustrated in figure B.
Installing and Removing the Battery Pack from
the tool
Warning! Make certain the lock-off button is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack (Fig. C)
Insert battery pack firmly into tool until an audible click is
u
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
Depress the battery release button (12b) as shown in
u
figure D and pull battery pack out of tool.
Hang hook (Fig. E)
Warning! Remove nails from magazine before making any
adjustments or servicing this tool. Failure to do so may result
in serious injury.
Warning! To reduce the risk of serious personal injury,
place the forward/reverse button in the lock-off position or
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! To reduce the risk of serious personal injury, ensure
the screw (15) holding the hang hook is secure.
Caution: When not in use, place tool on its side on a stable
surface where it will not cause a tripping or falling hazard.
Some tools with large battery packs will stand upright on the
battery pack but may be easily knocked over.
Note: When attaching or replacing the hang hook (14) use
only the screw (15) that is provided. Be sure to securely
tighten the screw.
(Original instructions)
If the hook is not desired at all, it can be removed from
the tool.
To move the hang hook, remove the screw (15) that holds the
hang hook (14) in place.
Note: Various trackwall hooks and storage configurations are
available.
Please visit our website www.stanley.eu/3 for
further information.
Operation
Warning! Read the section titled Nailer Safety Warnings
at the beginning of this manual. Always wear eye and ear
protection when operating this tool. Keep the nailer pointed
away from yourself and others. For safe operation, complete
the following procedures and checks before each use of
the nailer.
Warning! To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, clearing a jammed nails, leaving
work area, moving tool to another location or handing the tool
to another person.
Warning! Keep fingers AWAY from trigger when not driving
fasteners to avoid accidental firing. Never carry tool with finger
on trigger.
Wear proper eye, hearing and respiratory protection.
u
Remove battery pack from tool and engage trigger
u
lock-off.
Lock the pusher in the back position and remove all nail
u
strips from the magazine.
Check for smooth and proper operation of contact trip and
u
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
Never use a tool that has damaged parts.
u
Warning! Operate the tool with fasteners at a rate not
exceed 30 times/min.
To operate the nailer
Warning! The contact trip needs to be depressed followed by
a full trigger pull for each nail followed by a release of both the
contact trip and trigger after each nail.
Warning!The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Fully depress contact trip (8) against the work surface.
u
Fully pull trigger (1) and motor will start. (nail will drive into
u
work surface).
Release trigger.
u
Lift contact trip off work surface.
u
Repeat the above 4 steps for next application
u
ENGLISH
9