DeWalt DWH161 Manual Del Usuario página 35

To Remove the Battery Pack from the
Dust Extractor
1. Press the release button 2
out of the dust extractor.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 14 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Attaching the Carry Strap (Fig. C)
Your dust extraction system comes with a carry strap
can be connected to the carry strap hooks
as shown in Fig. C.
Attaching the Crevice Tool (Fig. A)
• To attach the crevice tool 12
insert the end of the dust extractor hose into the open end
of the accessory with a twisting motion until tight.
nOTE: The dust extraction hose is not compatible with
AirLock® connectors.
• To remove the crevice tool, hold the dust extraction hose
and pull the accessory off using a twisting motion.
Installing the Belt Hook (Fig. K)

WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the dust
extractor from a work belt. DO NOT use the belt hook
for tethering or securing the dust extractor to a person
or object during use. DO NOT suspend dust extractor
overhead or suspend objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
IMPORTanT: When attaching or replacing the belt hook
use only the screw 16 that is provided. Be sure to securely
tighten the screw.
If the hook is not desired at all, it can be removed from the
dust extractor.
and firmly pull the battery pack
10 that
11 in either manner
to the dust extractor hose 6
20
Attaching the Suction Cup to the
Dust Extractor (Fig. E)

WARNING: Use this attachment only with D
recommended dust extractors. For more information
about D WALT dust extractors compatible with this
e
attachment, please contact your local dealer or visit
www.dewalt.com.
Push dust extractor hose
until tight.
Attaching the Suction Cup to a Vertical or
Horizontal Surface (Fig. F, G)
The suction cup 13 can be fixed into place on a vertical or
horizontal surface.
1. With the suction cup securely connected to the dust
extractor, turn the dust extractor on.
2. Place the suction cup onto the floor or wall and press firmly
to engage the cup to the surface.
Removing the Suction Cup from a Surface

WARNING: DO NOT turn off the dust extractor before
removing the suction cup from the surface as instructed.
Turning off the dust extractor before removing the suction
cup will result in the suction cup falling from the surface
which could cause injury.
To remove the suction cup
,
attached, pry the lip away using your hand. Do not remove by
pulling on the hose.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
Proper Hand Position (Fig. A, D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
If used as a stand alone dust extractor, proper hand position
requires one hand on the accessory.
Using the Dust Extractor (Fig. A, E)
,
• Before using the universal dust extractor, ensure that the
filter is in place and filter box is securely fitted.
• Do not use damaged filters. Replace any damaged
filters immediately.
EnGLIsh
WALT
e
6 into the connection point 15
13 from the surface to which it is
33