DeWalt DWH161 Manual Del Usuario página 36

EnGLIsh
• Please observe national applicable regulations/laws on how
to handle harmful types of dust in your country.
1. Attach the appropriate accessory to the dust extractor
hose 6 .
2. Insert the battery pack 1 .
3. To turn dust extractor on, press the three position switch
to the On (I) position.
4. To use in Wireless Tool Control mode press the three position
swtich to the Wireless Tool Control ( ) position. Once
paired the trigger of the connected tool will control the
dust extractor.
nOTE: Refer to Pairing the Dust Extractor with a Tool
using Wireless Tool Control Mode to use the dust extractor
with a Wireless Tool Control equipped tool.
5. When finished, turn the dust extractor off by pressing the
three position switch to the Off (O) position or releasing the
trigger of the Wireless Tool Control equipped tool.
Pairing the Dust Extractor with a Tool Using
Wireless Tool Control Mode (Fig. A, H)

CAUTION: When the dust extractor is being controlled by
a paired power tool it may start or stop without warning.
To Pair with a D WALT Remote or Wireless Tool
e
Control Tool
1. Press the three position switch
Control ( ) position.
2. Press and hold the Wireless Tool Control pairing button
on the DWH161 and pull the trigger on the Wireless Tool
Control equipped tool or press the button on the remote at
the same time.
3. The LED 9 will be steadily illuminated to indicate a
successful pairing.
nOTE: Only one transmitter can be paired to the DWH161
at a time. If the unit is already paired the previous transmitter
will be overridden.
To Unpair with a Wireless Tool control Tool
• Press and hold the Wireless Tool Control pairing button
on the DWH161 and pull the trigger on the Wireless Tool
Control equipped tool or press the button on the remote at
the same time.
• The LED 9 will flash slowly to indicate a
successful unpairing.
Wireless Tool control Troubleshooting
LED Light Pairing Button
Pattern
Slow flash Not pressed
Fast flash Pressed
Solid Not pressed
34
7
7 to the Wireless Tool
8
8
system status
Wireless Tool Control not paired
Pairing Mode, Waiting for
signal from tool
Wireless Tool Control paired,
Waiting for command from tool
Filter Cleaning Mechanism
Suction power is dependent on the condition of the filter.
Therefore, the filter should be cleaned regularly.
The filter cleaning mechanism is a feature that uses the motor
in the dust extractor to force air through the filter. Refer
to Emptying the Dust Collection Box for instructions on
proper use.
Emptying the Dust Collection Box (Fig. I, J)

WARNING: The vacuum cleaner contains dust particles
that pose a risk to health. Emptying and maintenance
procedures, including the disposal of dust collectors,
should only be carried out by professionals. Suitable
protective equipment is required. Do not operate the
vacuum cleaner without the complete filter system.
Otherwise you endanger your health.

WARNING: Wear approved eye protection and approved
dust mask when performing this procedure.

CAUTION: Do not clean with water or compressed air.
The dust collection box 3 should be emptied as soon as the
performance has noticeably decreased or is full.
1. Press the dust collection box release buttons
dust collection box away from the dust extraction system.
Once the catch mechanism is clear of the dust extraction
system the upper joint will also release allowing the dust
collection box to be removed completely.
2. To empty the dust collection box
suitable container to catch the dust contained within it.
Lift up the assembly release latch
collection box, separating the canister from the lid. Gently
tapping the dust collection box will encourage any dust
trapped within the filter to also be removed. Once the filter
lid and canister are empty reattach them, ensuring the
assembly release latch 18
Figure J.
3. To reattach the dust collection box to the dust extraction
system first insert the rounded profile of the upper joint
into the recess on the dust extraction system. Pivot the dust
collection box down so that the release buttons click back
into place. Refer to Figure I.
4. With the dust collection box properly installed, depress the
filter cleaning mechanism
Allow the system to run for 5 seconds and release trigger.
This should be done after every emptying of the dust
collection box.
Transporting the Dust Extractor

WARNING: Accidental start up during transport could
be hazardous. Always transport the dust extractor
with the batteries removed. Refer to the Battery
Packs, Transportation section of this manual for
further information.

WARNING: Check the tool and batteries for damage after
transport and before use.
4 and pull the
3 position it over a
18 to open the dust
is securely fastened. Refer to
5 and turn on the dust extractor.