Technical Data; Noise / Vibration Information; Filling The Magazine - KMR 3418 1 Serie Manual Del Usuario

4 I English
1

TECHNICAL DATA

Type
Dimensions mm
Weight kg (without fasteners)
Single sequential or contact actuation
Recommended operating pressure
range
Maximun permissible operating
pressure
Air consumption per driving
operation
Magazine capacity
(T-nails/finishing nails/staples)
Penetration depth setting
Fasteners:
T nails
T-nail length mm
T-nail shank Ø mm
Finishing nails
Nail length mm
Nail shank Ø mm
Staples G
Staple length mm
Wire thickness mm
Staple width mm
Staples H
Staple length mm
Wire thickness mm
Staple width mm
Recommended lubricant
1 litre special oil. Code No.
250 cm3 grasa especial. Code No.
2

NOISE / VIBRATION INFORMATION

Noise characteristic values *
A-weighted single-event emission sound
pressure level at work station L pA, 1s
A-weighted sound power level
L WA, 1s, d
Vibration characteristic values **
Weighted r.m.s.-acceleration (a)
The noise level when working can exceed 85
dB (A). Wear ear protection!
* Measured values determined according to EN 12549:1999.
** Measured values determined according to ISO 8662-11:1999.
KMR
3
3418...1
1
1
320/330
1
3.3 kg
4
5-8,5 bar/
0.5-0.85 MPa
Only those fasteners specified under technical data
8.5 bar/
(see 1) may be used.
0.85 MPa
When filling the magazine, hold the tool so that the
2.6 l at 6
muzzle is not pointing towards own body or towards
bar / 0.6 MPa
any other person.
Do not load the tool with fasteners with the safety
yoke or trigger depressed.
80/90/100
yes
Press the locking lever (l) and pull the top of the
magazine (o) back. Finishing nails and T-nails are
inserted point first in the centre of the magazine.
Staples are pushed over the ridge of the magazine.
32 - 65
Then push the top magazine forward until it locks
2.2
into place.
Nails and staples may not be in the magazine at the
same time.
32 - 60
2.2
5
32 - 64
The penetration depth of the nail head can be
1.4 x 1.6
controlled by means of the air pressure. If this is
not satisfactory, the penetration setting offers a
11.7
more accurate adjustment of the penetration depth.
Adjustment is only possible in the unpressurized
44 - 64
condition.
1.6 x 1.9
12.3
9 4420
Change the penetration depth by turning the setting
68 3868
ring(qu) using the Allen key supplied or a pin with max.
diameter of 4.5 mm (0.18 inch).
Turning from hole to hole in the setting ring causes a
change by 0.2 mm (0.008 inch). The setting distance
is 6 mm (0.236 inch). The setting can be judged by the
3418...1
distance of the screw head in relation to the contact
face on the flange (k) (max. distance = 6 mm (0.236
inch), largest penetration depth of the fastener).
82 dB(A)
95 dB(A)
6
Towards the front the driver channel is closed by
3 m/s2
flexible means. When distortion of a fastener occurs
the channel is flexibly widened and the distorted
fastener is automatically discharged. The nailer
continues to be operational.
Extreme jamming can be eliminated without the aid of
tools. In this case, disconnect the nailer from the
supply hose without fail.
SUPPLIED WITH
Combination Nailer
Tool use and safety instructions
Technical data sheet

FILLING THE MAGAZINE

FIL PENETRATION DEPTH SETTING
NAIL GUIDANCE (FIG. 1 AND 2)
3418...1