MTD SMART RG 145 Manual De Instrucciones página 12

English
Note
Do not use the OCR function
unless absolutely necessary,
otherwise work with the key in the
normal position. The OCR function
switches off automatically as soon
as the key is turned to the normal
position or the engine is switched
off (stop position or disconnection
of the engine by the safety interlock
system).
Choke
(depending on model)
Fig. 7
To start a cold engine, pull the
choke (Fig. 7a), or move the acce-
lerator lever to (Fig. 7b).
Throttle
Fig. 8
Set engine speed continuously.
Fast engine speed =
Slow engine speed =
Clutch/brake pedal
(only for models with
Transmatic drive)
Fig. 9
Clutching = Depress pedal half
way.
Braking = Depress pedal all the
way.
Note
Is also used to activate/deactivate
the parking brake.
Brake pedal
Fig. 9
Brake = Depress pedal.
Note
Is also used to activate/deactivate
the parking brake.
Direction-of-travel lever
(only models with
Transmatic drive)
Figure 10
The direction lever must be used
only when the tractor is stationary.
12
To do this, depress the clutch/
brake pedal all the way and keep
depressed.
Forwards = Lever to "F/ "
Idling = Lever to "N"
Reverse = Lever to "R/ "
The device must first be stopped
prior to each change of direction.
Cutting height adjustment
lever
Figure 11
Largest cutting height, cutters top
= lever to "5 (H)".
Smallest cutting height, cutters
bottom = lever to "1 (L)".
PTO lever
Figure 12
The PTO lever mechanically swit-
ches the cutter deck on and off.
Switch off cutter deck 0 /
.
= pull lever all the way backwards
.
Switch on the cutter deck I /
= slowly push the lever forwards to
the stop
Parking brake for units with
hydrostatic drive / automatic
drive
Figure 13
Actuate the parking brake: Fully
depress brake pedal and move
lever to position "I".
Release the parking brake:
Depress the brake pedal all the
way and move the lever to the "0"
position.
Lever for speed settings/
parking brake for units with
Transmatic drive
Fig. 14
Low speed = Lever on "1".
High speed = Lever on "6" or "7"
(optional).
Increase speed = Adjust drive posi-
tions without actuating the clutch/
brake pedal.
Reduce speed = Adjust drive posi-
tions by actuating the clutch/brake
pedal (depress halfway).
Operating instructions for lawn tractors
Actuate the parking brake: Fully
depress clutch/brake pedal, push
lever for speed setting to
Release the parking brake: Fully
depress clutch/brake pedal, push
lever to a speed setting.
Drive lever for units with
hydrostatic drive
(depending on model)
Fig.15
Using the drive lever, set the speed
steplessly and change the driving
direction.
Forwards:
Fast forward driving
= Lever to "F/ ".
Maximum mowing speed
= Lever to „ /
Stopping:
To stop driving and change direc-
tion = lever to "N".
Backwards:
Reverse driving = lever to "R/ ".
Note
– The further the lever is pressed
towards "R" or "F", the faster the
unit moves.
– When the brake pedal is actu-
ated and released again, the
drive lever moves towards the
"N" position and reduces the
operating speed.
Accelerator for units with
hydrostatic drive (depending
on model)/automatic drive
Fig. 16
The drive pedal is used to adjust
the speed continuously and to
change direction:
Forwards = push forwards the
accelerator pedal (in direction
the further forward, the faster.
Stop (for stationary vehicle and
changing direction)
= release the drive pedal (N).
Reverse = push back the accelera-
tor pedal (counter to direction
the further back, the faster.
Note
When the parking brake is applied,
the accelerator cannot be actuated.
.
".
),
),