Kettler ST 7849 Instrucciones Informáticas Y De Formación página 7

Functions and Operation of the Training Computer
RPM /SPEED (left)
In this display, at turning intervalls (every 6
seconds), the pedaling frequency as RPM
(=rotations per minute) and the speed SPEED
in km/r are shown. The highest speed is
99.9 km/h.
TIME (2nd left)
In this display the exercise time is mea-
sured. The maximum time measurement is
99:99 minutes.
DISTANCE (middle)
The distance covered is measured in km.
The counting of the distance begins with
>0< and a maximum of up to 99.9 km can
be shown. The counting grading follows
in 0.01 km sections = 10 meters.
CALORIES (2nd right)
In this display the calculated calorie con-
sumption is displayed. The maximum
display is 9999.
The data however only serves as a rough
guideline in comparison to the different
exercises and cannot be used for medical purposes.
PULSE (right)
If you hold the hand grip sensors with both
hands, the display shows the current pulse fre-
quency value. You can enter a target value
before beginning exercising. If the pulse fre-
quency has exceeded this target, an alarm
sounds in order to inform you of this.
SLEEP MODE (empty)
If no RPM or PULSE are recorded or no manual settings have been
made within 4 minutes, the device switches to the sleep mode.
In this mode, the time, as a large display, the temperature and
the date with month, day and year are shown.
4. Personal exercising specifications
General
- Without particular preliminary settings, the values in the indi-
vidual functions [TIME, DISTANCE; CALORIES and PULSE]
count from >0< upwards.
- For reasonable exercising, it is sufficient to merely set a target
value in one function [TIME, DISTANCE, CALORIEN or PULSE].
- If a personal target value is set as an exercise specification,
the computer counts from this value downwards. When rea-
ching the target value >0<, an acoustic signal sounds off. If
afterwards, without setting of a new target value, you continue
exercising, the computer counts in this mode from >0<
upwards again.
All manuals and user guides at all-guides.com
- Once target values have been set, during exercising these
cannot be changed, only during a standstill.
Target value specifications
The setting of the target values is the same with all functions:
e.g. DISTANCE
1. Press the MODE key until in the field the number blinks in
the field DISTANCE and the large number is in the display
(identification left > DST).
2. Through shortly pressing the key SET, you increase the value.
E.g. DISTANCE in 0.5 km steps. If you press and hold the
SET key, the set value is counted quicker.
3. If you would like to reduce the target value again, shortly
press the RESET KEY: Counting will begin again from >0<.
Press the SET key again until the target value has been
reached.
4. If you have set the target value, press the MODE key. The
value is then stored in this function and you go to the next
function, e.g. CALORIES.
5. Enter the specification values if possible only in one function
because otherwise the exercise goals will be overlapped.
E.g. if you would reach the preset time goal earlier than
the preset distance goal.
6. The specified values in the other functions [TIME; CALORIES
or PULSE] are, as described with 1-4, also entered with the
keys SET, RESET and MODE.
After finishing the presettings, you can begin with exercising.
During the exercise session, in the display the display of the dif-
ferent functions changes every 6 seconds. If you press the
MODE key during this display, the selected function remains in
the display in large numbers. In the small display the function
name blinks, e.g. PULSE.
Pressing the MODE key again operates the SCAN operation >
display change every 6 seconds.
RECOVERY
With the RECOVERY key, you reach a recovery pulse measu-
rement at the end of the exercise session. From the beginning
and ending pulse of one minute, the deviation and the fitness
grade is determined. With the same exercise session, the impro-
vement of this grade is a measurement of the increased fitness.
If you have reached the target value, end the exercise session,
press the RECOVERY KEY and then lay your hands on the hand
pulse sensors. With a previous pulse measurement in the display
00:60 appears for the time and in the PULSE display the current
pulse value blinks. The time begins to count from 00:60 back-
wards. Keep your hands on the hand pulse sensors until >0<
GB
7