GM 90801519 Guia De Inicio Rapido

Rear Compartment Lid Spoiler Package
Parts List
Description
Spoiler Assembly
Nut (M6)
Template
Instruction Sheet
Solvent Package
Installation Time
Approximately 30 minutes
Painting Instructions
For top coating, refer to the applicable paint manufacturer's directions.
Tools Required
Drill
Center Punch
Clean Shop Towels
Masking Tape
1/8" Drill Bit
3/8" Drill Bit
Torque Wrench
1/4" Drive - Universal joint
Anticorrosion Compound (GM P/N 12371287 or touch up paint)
Vehicle Preparation
1. Vehicle body surface and spoiler temperature should be between
Û) DQG Û) Û& 
2. Clean vehicle decklid area with soap and water to remove residue
prior to installation.
3. For best results, trunk lid should be free of damage (dents, scuffs,
creases, fractures, etc.).
4. Do not use petroleum based cleaning products. If a strong cleaner
is required, we recommend using 3M general purpose adhesive
cleaner (PN 08984) with a clean cloth to remove all visible
contaminates (road tar, etc.). It may take the use of several cloths
to obtain a clean surface. It is important to replace the cloth when
soiled or you will be smearing or wiping contaminates back on
the vehicle. After using the Adhesive Cleaner, use the SOLVENT
PKG-BODY SURF CLNR; (PN 12365938 14W 0849Z 0030).
5. 3ODFH D GURS FORWK LQVLGH WKH WUXQN VR WKDW LW VXI¿FLHQWO\ FRYHUV
the area under the trunk lid.
Rear Compartment Lid Spoiler Package
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
22SE12 Initial Release - Feng Zhaobin
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE
WITH GM SPECIFICATIONS.
Quantity
1
3
1
1
1
De-burring Tool
Safety Glasses
Small Hammer
Alcohol Cleaner
1/4" Drive Ratchet
1/4" Drive Extension
1/4" Drive - 10mm Socket
AUTH
REVISION
1807861
Spoiler Installation
NOTE: To optimize decklid opening and closing efforts there are 2
coil springs, located one on each side of the decklid opening behind
the trim. These springs control the opening force and closing force
of the decklid and are attached to the rear end panel by a bracket.
To decrease the opening efforts, the notch closest to the rear end is
where the spring should be positioned. To adjust the springs, remove
the trim and pull the spring to the notch closest to you on each side.
[Please refer to decklid trim removal instructions.]
[Please refer to decklid trim side removal instructions.]
For better operation, especially in the cold with the spoilers, it is
recommended that both springs be moved to this rearward
most location.
1. Paint the spoiler if required.
1RWH 3ULRU WR ¿QLVKLQJ RU UH¿QLVKLQJ UHIHU WR *0 0'
5H¿QLVKLQJ 0DQXDO IRU UHFRPPHQGHG SURGXFWV 'R QRW
FRPELQH SDLQW V\VWHPV
UHFRPPHQGDWLRQV IRU IXUWKHU LQIRUPDWLRQ
2. Remove the decklid liner.
3. Place the template on the rear decklid with the writing facing up.
4. Align the printed line on the forward edge of the template with
the forward edge of the decklid.
PART NO.
IR 22SE12
INSTALLATION INSTRUCTIONS
DR
TITLE
Rear Compartment Lid Spoiler Package
PART NO. 90801519
Original Spring Location
Updated Spring Location
5HIHU WR SDLQW PDQXIDFWXUHU
90801519
SHEET
1
SHEET
1 6
OF
6
OF