Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
FOR
INSTALLATION
OF 58058 OR 30035
RAIL KITS
1.
Do not install mounting rails over plastic bed liners. Plastic bed liners must be cut out of the way to provide metal to metal
contact. Mounting rails may be installed on spray in liners.
2.
Use only bolts, nuts, and washers supplied to install this kit. All bolts & nuts are Grade 5 unless otherwise specified.
3.
These instructions are guidelines only, actual installation is the responsibility of the installer and the owner. Always measure
truck and trailer before installing hitch to be sure that there is clearance at the cab and at the bumper to allow for turns.
4.
Lower and remove spare tire and lower exhaust if extra room is needed. Remove inner plastic wheel well liner to allow
access to frame.
5.
Detach the electrical wire loom and brake lines from the inside driver side of the frame.
6.
Place the rear mounting rail in the box of the truck, using your tape measure, center the rail between the weld seams on the
length of the truck box floor and the proper distance from the rear edge of the truck box as shown in Figure 2.
Note: It is critical that rail is centered side to side on the truck bed.
7.
Mark and center punch the holes as shown in Figure 2 (Rows 1 & 2). Remove the rail and drill each position with a 1/8" drill
bit.
Note: There
8.
Temporarily position the frame bracket on the outside of the frame and check that the 1/8" drilled holes align with the slots of
the frame bracket. Remove the frame bracket from the vehicle.
9.
Enlarge the 1/8" drilled holes
bottom of the bed sill requires a 9/16" hole. Paint all bare metal.
10.
Loosely install the frame brackets rear (3)(4) by attaching the bolts (6), conical washers (7). (See Figure 1)
11.
Install tube spacer (Item 9)
12.
Move rear mounting rail into position. Install the 1/2"-13 x 2" carriage bolts that are supplied with the rails
4-1/2" from this kit
with the block spacer. Block spacers to be located in the corrugation between the box and the mounting
rail or between the box and
13.
The 1/2"-13 x 2" hex head bolts (10), may be used in place of the carriage bolts on the rearward most rail attachment if it is
difficult to install carriage bolts. (Note the block spacer is to eliminate crushing bed corrugation.) Attach .25" x 1" x 3"
block (5), 1/2" conical washers and ½" nut to the underside of the brackets per the illustrations and tighten snug to keep the
mounting rail from moving. (For Row 1)
14.
The forward side of the rear rail's holes (row 2) will fasten through the bed sill as shown in Figure 1 with the tube spacer, 4-
1/2" carriage bolt, ½" conical washers and ½" nut fastening to the underside of the bed support.
15.
Place the unassembled 5th wheel saddles/slider/goose into the already installed
rail with the saddles/slider/goose by inserting the tabs into the mounting rail and pushing the mounting rail tight towards the
other mounting rail. Ensure that the mounting rail is centered between the weld seams
This will position the mounting rail in the correct location and ensure that the 5th wheel will have a snug fit to the truck.
NOTE: If more than one hitch product will be used with the rails then both should be used at the same time to align the second
rail. This will ensure that one product does not compromise the fit of the other.
16.
Mark, center punch, and drill 1/8" holes per figure 2 for row 3 and
all bare metal.
17.
Move the
front
mounting rail into position. Install the 1/2"-13 x 2" carriage bolts with the block spacer to be located in the
corrugation between the box and the mounting rail or between the box and front brackets (1) (2). (Note the block spacer is to
eliminate crushing bed corrugation.) The rear end of the front brackets (Row 3) will be attached using the1/4" x 1" x 3"
block (5), ½" conical washers and ½" nut
spacers, washers and nuts as per the illustrations and tighten snug to keep the mounting rail from moving.
After fully installing the 50054 custom mounting brackets, tighten the fasteners in the following sequence. Note: Torque all
18.
1/2" hardware to 75 ft-lbs 102 (N*M) and all M12 hardware to 92 ft-lbs (125 N*M). First torque the mounting rails to
the frame brackets and then torque the frame brackets to the truck frame.
19.
Reinstall electrical wire loom and brake lines. Replace inner plastic wheel well liner to body, if removed, reinstall spare tire.
2014, 2015 Cequent Performance Products
©
Printed in Mexico
Installation Instructions
CUSTOM QUICK INSTALL
MOUNTING KIT
will
be drilling through the
top and bottom of
Enlarge the 1/8" drilled holes in row 2 to 1-1/8" (bed corrugations only). The
in row 1
to 9/16".
frame
brackets.
as
shown in Figure 1. Attach the forward side of the front brackets (Row 4) with
Ram 2500
the bed sill perpendicular with the truck bed.
rear
4. Repeat steps 8
Sheet 2 of 6
50054N
Part Numbers:
50054
and the 1/2"-13 x
mounting rail. Position the front mounting
on the length
of the truck box floor.
and open these 1/8" holes to 9/16". Paint
03/31/15
Rev. D
Publicidad
Tabla de contenido
