Erp Function; Bluetooth & App; Cleaning And Maintenance; General Cleaning - Tunturi T60 Treadmill Performance Manual De Usuario

program, press "Mode" button to confirm.
- Set your age the display shows "25"
Press "Up/ Down" buttons to select:1~99
press "Mode" button to confirm.
- Target heartrate will be show, based on your set age. Target heart
rate = (220-age) x0,6.
Press "Up/ Down" buttons to change target value 60~200) press
"Mode" button to confirm.
- Set your workout time the display shows "30:00"
Press "Up/ Down" buttons to select: 5:00~99:00
press "Mode" button to confirm.
- Press the "Start/ Pause" button to start the program.
HRC operating function:
- HRC programs starts with a one minute warm up time. ( speed will
not auto adjust )
- The initial speed is 1.0 km/h, this can be adjust to a comfortable
warm up speed manually.
- Console checks heart rate every 30 seconds and controls the speed
as below.
Heart rate parameter
29+ BPM Under target
6~29 BPM Under target
0~5 BPM Under target
0~5 BPM Over target
6~29 BPM Over target
29+ BPM Over target
‼ NOTE
• Incline setting is not controlled in HRC program mode but
can be controlled by user at any time to intensify or ease your
workout.
• Speed can be changed by user at all times.
• When speed is over the pre set speed limit it will auto adjust to
pre set speed setting automatically.
• If no heart rate is detected, the treadmill will stop workout.
⚠ CAUTION
• Heart rate measurement is required for this function.

ERP Function

ERP function can shut your treadmill in sleep mode automatically
when being without operation for 4:30 minutes.
You can turn this function On and off by:
- When treadmill is in "start up mode" press and hold "Mode"
button for 3 seconds to switch between On and Off mode.
• Display shows "1111" indicates On mode.
Machine will turn to sleep mode after 4:30 minutes being idle.
• Display shows "2222" indicates Off mode.
Machine will not turn into sleep mode after 4:30 minutes being
idle.
⚠ CAUTION
• We recommend to set ERP function in On mode always.
Bluetooth & APP
- This console can connect with an APP on a smart device by
Bluetooth (iOS & Android).
- Establish the Bluetooth connection only via the connection mode
on the installed APP on your smart device.
‼ NOTE
⚠ WARNING
- Do not block the ventilation openings. Keep the ventilation
speed adjust
- Clean the equipment with a soft, absorbent cloth after each use.
+ 2.0 Km/h
- Clean the visible parts of the equipment with a vacuum cleaner
+ 1.0 Km/h
- Regularly check that all screws and nuts are tight.
No adjust
No adjust
⚠ CAUTION
- 1.0 Km/h
- 2.0 Km/h

General Cleaning

Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis: vacuum underneath your treadmill
to prevent build-up.
UNPLUG POWER CORD BEFORE THIS TASK.
Belt Dust
This occurs during normal break-in or until the belt stabilizes. Wiping
off excess dust with a damp cloth will minimize build-up.

Belt and Running Deck

Your treadmill uses a very high-efficient low-friction bed.
Performance is maximized when the running deck is kept clean and
free from dust and dirt. Dirt and dust particles between running deck
and running belt will damage your running deck surface affecting
your performance and product lifetime.
How to clean running deck
Use a soft, dry, non-abrasive cloth to wipe the edge of the belt and
the area between the belt edge and frame. try to reach under the
running belt edges too, to remove the dirt build up on the edges too.
How to clean running belt surface
Firstly use a nylon scrub brush to remove the loose particles from the
running belt surface. Than use wrung out damp cloth (no cleaners or
abrasives) to gentle clean the top of the textured belt. Allow the belt
to fully dry before using.
2 3
• Tunturi only provides the option to connect your fitness console
throughout a bluetooth connection. Therefore Tunturi cannot
be held responsible for damage, or malfunctioning of products
other than Tunturi products.
• Check the website for extra information.

Cleaning and maintenance

• Your trainer requires monthly maintenance, even when not being
used.
• Before cleaning and maintenance, remove the mains plug from
the wall socket.
• Do not use solvents to clean the equipment.
openings clear from dust, dirt and other obstructions.
with a small suction nozzle
• We recommend to use indoor shoes only on your treadmill.
When you don't have these we do recommend to check the
soles of your footwear before using them on your treadmill.
The treadmill is not sustainable for dirt from outdoors.
‼ NOTE
• When your belt too dirty to clean with water only, you can use a
mild soap, but never a lubricant solvent.
GB