Cooper Lighting Crosstour LED Manual Del Usuario

INSTALLATION INSTRUCTIONS
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
SAFETY: This fixture must be wired in accordance with the National Electrical Code
and applicable local codes and ordinances. Proper grounding is required to insure
personal safety. Carefully observe grounding procedure under installation section.
WARNING: Make certain power is OFF before starting installation or attempting any
maintenance. Risk of fire/electric shock. If not qualified, consult an electrician.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
TOOLS REQUIRED: Phillips head screw driver and electrical wiring tools.
STEP 1. Loosen the knuckle pivot screw. Adjust the position of the knuckle stem.
Re-tighten.
STEP 2. Route electrical leads through the 1/2" NPS cover plate (supplied by others).
Seal knuckle threads with sealing compound (provided by others).
Secure cover plate to knuckle with lock nut (50-60 in-lbs). Make wire
connection in outdoor rated junction box. Mount cover plate to junction box.
CAUTION: DO NOT mount the cover plate to junction box prior to mounting knuckle
flood base assembly to cover plate. This can result in twisted wires causing
connections to break which can create a shock hazard when powered.
STEP 3. Separate Crosstour housing door from the back box. Remove the indicated
gasket punch outs on the back box.
STEP 4. Use the supplied four (4) 8-32 x 1/2" Phillips head screws to attach the
back box to the knuckle flood base assembly. The wire leads must be pulled
through the center wire way hole. Utilize the locating tab on the knuckle
flood base plate to align to the back box. Tighten/torque all four screws to
30-40 in-lbs. Ensure all screws are equally tight. Ensure that the knuckle
plate is FULLY compressed against the back box. Full compression will
result in no visible gap between the back box and knuckle flood base.
STEP 5. Make wire connections between the knuckle leads and Crosstour luminaire
leads (refer to wire diagram). Re-attach door to housing tighten/torque to
15-20 in-lbs. Attach optional visor and impact guard (See STEPS A-B).
STEP 6. Adjust aiming angle of the fixture by loosening the pivot screw. Use visual
angle indicators to set desired angle. Tighten/torque pivot screw 50-60
in-lbs.
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user's purpose, please contact
your nearest representative. NOTE: Specifications and dimensions subject to change without notice.
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
ADH120435
4/10/2012
• RISK OF ELECTRIC SHOCK—Disconnect power at fuse or circuit breaker before
installing or servicing.
• RISK OF BURN—Disconnect power and allow fixture to cool before servicing.
• RISK OF PERSONAL INJURY—Fixture may become damaged and/or unstable if not
installed properly.
• DO NOT mount luminaire within 6" of a combustible surface. DO NOT handle
luminaire by the glass.
STEP 1 and 2
STEP 4
STEP 5 Crosstour without Photocontrol
Supply Line (Black)
Connect all
Ground Wires First
Load (Black)
Neutral (White)
Supply Neutral (White)
Crosstour with Photocontrol
Supply Neutral (White)
Load (Red)
Neutral (White)
Line (Black)
Wire Nut Supplied by Others
STEP 6
Crosstour LED
TM
Knuckle Kit
Sheet 1 of 4
IMI-770
STEP 3
Center Wireway Outer Slot
Locating Tab
LED
DRIVER
Factory Wired
LED to Driver
Load (Black)
LED
DRIVER
Neutral (White)
Factory Wired
LED to Driver
Supply Line (Black)
15°