Cooper Lighting HALO TGS3S401MSRB Instrucciones

B. Mounting bracket
A. Light fixture
A. Light fixture
TGS3S401MSRB
TGS3S401MSRW
TGS2S402MRRB
TGS2S402MRRW
TGS2S402MSRB
TGS2S402MSRW
TGS3S403MRRB
TGS3S403MRRW
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
TGS3S301MSRB
(use the size that fits your junction box) D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
tion box screws (use the size that fits your junction box)
(use the size that fits your junction box)
TGS3S301MSRW
TGS2S302MRRB
TGS2S302MRRW
TGS2S302MSRB
TGS2S302MSRW
TGS3S303MRRB
TGS3S303MRRW
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 Volt, 60 Hz power source. Any other connection voids the
warranty.
• Fixture should be installed by persons with experience in household wiring or by
a qualified electrician. The electrical system, and the method of electrically con-
necting the fixture to it, must be in accordance with the National Electrical Code
and local building codes.
• Mount fixture to a grounded, recessed-mounted standard junction box marked for
use in wet locations.
• Fixture can be mounted to an outdoor rated surface mount junction box when
used with the adapter plate kit (sold separately TGS-KIT-MTG). See kit instruc-
tions for proper installation methods.
• For proper operation and protection against damage, the motion sensor head
adjustment knobs must be facing the ground.
• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.
• Do not mount below 5 feet.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following 2
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
Questions?/ Des questions? / ¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com
PACKAGING CONTENTS / CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
B. Mounting bracket
A. Light fixture
PACKAGING CONTENTS
PACKAGING CONTENTS
PACKAGING CONTENTS
Appareil d'éclairage Support de montage
PACKAGING CONTENTS
Accesorio Soporte de montaje
B. Mounting bracket
A. Light fixture B. Mounting bracket
A. Light fixture B. Mounting bracket
E. Adapter Plate Kit (Sold Separately)
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
Trousse de plaque d'adaptation
E. Adapter Plate Kit
E. Adapter Plate Kit
(vendue séparément)
E. Adapter Plate Kit
Kit de placa adaptadora
(se vende por separado)
#TGS-KIT-MTG
Instruction Manual / Manuel d'instructions/ Instrucciones
C. Gasket
C. Gasket
Joint d'étanchéité
Junta
C. Gasket
C. Gasket
B. Mounting bracket
C. Gasket
C. Gasket
F. Decorative screw cover caps
E. Adapter Plate Kit
F. Decorative screw cover cap
Cache-vis décoratif
F. Decorative screw cover caps
F. Decorative screw cover caps
Cubierta tapatornillos decorativa
F. Decorative screw cover caps F. Decorative screw cover caps
E. Adapter Plate Kit
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or modifica-
tions to this equipment not expressly approved by the manufacturer could void
the user's authorization to operate this equipment. NOTE: This device complies
with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference including interference that may cause
undesired operation of the device.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install the motion sensor 8-12 feet above the
ground. (Motion sensor is less sensitive above
12 feet.)
• Locate motion sensor so motion moves across
detection zone (Fig. 1).
• Locate sensor away from heat producing sources
to prevent false triggering. Also be very careful
not to include objects such as windows, white walls and
water in the detection zone.
• Locate sensor away from moving objects such as trees, large shrubs and street
traffic.
1
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
2 vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pour
boîtier de jonction
(2) cajas de empalmes de 6-32 x 3/4 pulgadas y de 8-32 x 3/4
pulgadas tornillos
G. Wire connector
Serre-fil
Conectores de cable
1
MOTION SENSOR
FIG.1