Steam Function; Grounding Instructions - Briggs & Stratton BPW1700 Manual De Instrucciones

To apply detergent, follow these steps:
1. Remove detergent tank and cap (1G,10). Fill with
detergent solution.
2. Replace cap and detergent tank.
3. Install black spray tip.
NOTICE Detergent cannot be applied with turbo, red or
yellow spray tip.
4. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
5. Allow detergent to "soak in" per detergent manufacturer's
instructions before washing and rinsing.
Pressure Washer Rinsing Figure
1. Remove black spray tip from wand (B) and install
yellow or red spray tip.
WARNING! Kickback from spray gun could cause
you to fall resulting in death or serious injury. Operate
pressure washer from a stable surface. Be extremely
careful if you must use the pressure washer from a ladder,
scaffolding, or any other similar location. Firmly grasp spray
gun with both hands when using high pressure spray to avoid
injury when spray gun kicks back.
2. Apply high pressure spray to a small area and check surface
for damage. If no damage is found, continue rinsing.
3. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Stopping Pressure Washer Figure
1. Release spray gun trigger.
2. Press master switch (1,L) to OFF (0) (9,A) position.
NOTICE Releasing the trigger will shut off the motor but
does not shut off electrical power to the unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction, press
trigger lock button, and squeeze trigger to relieve built
up pressure in the unit.
WARNING! The high pressure stream of water that
this equipment produces could cut through skin and
its underlying tissues, resulting in serious injury and
possible amputation. Keep high pressure hose connected to
pump and spray gun while system is pressurized. DO NOT
allow CHILDREN to play or operate pressure washer.
ALWAYS point spray gun in safe direction, squeeze spray
gun trigger to release high pressure, every time you turn off
pressure washer.
5. Disconnect PRCD plug (1,E) from outlet, and store
power cord.
6. Store high pressure hose (1,J) below water tank.
7. Store spray gun (1,A) and plastic wand (1,M) in
holders. Store spray tips (1,C) in holder on metal
wand. See Features and Controls.
6

Steam Function

Grounding Instructions

This pressure washer must be grounded. If it should
malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric
shock. This pressure washer is equipped with a cord having an
equipment grounding conductor and grounded plug. The plug
must be plugged into a properly installed and and grounded
outlet in accordance with all local codes and ordinances.
install a proper outlet by a qualified electrician. DO NOT use any
1
type of adaptor with this pressure washer.
NOTICE Use ONLY distilled water. DO NOT use any
other liquids that could be flammable or clog the system.
1. Remove water tank cap and tube from water tank (1,F).
2. Fill tank with distilled water.
NOTICE To ensure optimal pressure washer operation,
use ONLY distilled water. Limestone deposits could
compromise the pressure washer's normal operation
intermittent steam supply, water leaks, nozzle and pipe
clogging). If this occurs, please contact a Briggs & Stratton
authorized Service Service Dealer. DO NOT use any other
liquids that could be flammable or clog the system.
3. Place suction tube and cap in water tank.
1 9
touch steam jet or nozzle end with hands during use. Allow
equipment to cool before touching. ALWAYS point steam
gun in safe direction while system is operating. DO NOT
aim steam gun at people or animals.
NOTICE Garden hose and high pressure hose do not
need be connected to use the steam function.
4. Perform Steps 1 - 5 in Starting Pressure Washer.
5. Turn master switch to STEAM function position (II) (9,C) and
wait 60 SECONDS for steam to build to function adequately.
NOTICE When steam gun trigger is first squeezed,
a small amount of water may precede steam. ALWAYS
point steam gun in a safe direction.
NOTICE Never let water in tank run out completely. Refill tank
when the water level reaches 1/4 full. Operating the pressure
washer without water can damage the boiler feed pump.
6. Point gun in a safe direction, disengage trigger lock and
squeeze trigger. Steam will release from the nozzle.
1 9
WARNING! Improper connection of the grounding
conductor can result in a risk of electrocution. Do not
modify pressure washer plug. If it does not fit the outlet,
WARNING! Hot surfaces and steam
produced by the steam gun could cause
burns resulting in serious injury. DO NOT
BRIGGSandSTRATTON.COM