ROBBE Nano-Vector ARF Manual De Instrucciones página 3

Specification
Wingspan: approx. 580 mm
Overall length: approx. 510 mm
Total surface area: approx. 10 dm²
All-up weight: approx. 350 g
Total surface area loading: approx. 35 g / dm²
Dear Customer,
Congratulations on your choice of a factory-assembled model air-
craft from the robbe Modellsport range. Many thanks for placing
your trust in us.
The model can very quickly be completed ready to fly. Please read
right through these instructions and the separate information sheets
before attempting to assemble and fly the model, as this will make
it much easier to complete the tasks required.
We constantly strive to update our products to reflect the latest
developments. You can find details of technical improvements
and revised documentation on the Internet by calling up the
appropriate product description at our website: www.robbe.
com.
All directions, such as "right-hand", are as seen from the tail of
the model, looking forward.
Notes on the power system
A brushless outrunner motor and impeller (ducted fan) are already
installed in the fuselage.
The motor is connected to the speed controller, ready for use.
To complete the power system all you have to do is connect the
LiPo flight battery.
Instructions for setting up the speed controller are included in
the Appendix to the instructions.
The radio control system
For this model you require a radio control system with at least four
channels and a delta mixer. We particularly recommend 2.4 GHz
systems.
The servos for the combined ailerons / elevators are already
installed.
The receiving system is powered by the speed controller's integral
BEC system.
© robbe Modellsport
All manuals and user guides at all-guides.com
Assembly and operating instructions
Nano-Vector ARF
Before you check the model's working systems, set the control
surface servos to neutral from the transmitter (transmitter sticks and
trims central).
Before flying the model always move the throttle stick to the "motor
stopped" position before switching the transmitter on. Only then
connect the flight battery.
To switch off, first disconnect the flight pack from the speed control-
ler, and only then switch the transmitter off.
When installing or setting up the receiving system compo-
nents, including the speed controller, be sure to read and
observe the instructions supplied with them.
You should also read right through the instructions and safety
information supplied with the battery pack and charger before
using these items for the first time.
Joining the components, recommended adhesives
All parts must be trial-fitted "dry" (without glue) before you
reach for the glue.
robbe Speed 1
Activator spray
Please take great care to avoid excess adhesive running onto the
painted surfaces, as this will damage the finish.
Recommended accessories
Description
T-6 EX-R6308SBT 2.4 GHz
radio control system
Transmitter battery 8NIMH 2000
ROXXY® POWER ZY 3S 1000mAh 30C
2x ROXXY® POWER ZY 2S 1000mAh 30C
wired in series
Connector for battery
Heat-shrink tubing 4.8 D
Battery charger, e.g.
POWER PEAK® Uni 7 EQ, 230V
Transmitter battery charge lead
Battery charge lead
Velcro (hook-and-loop) tape
Kit contents
- Ready-made EPO foam parts set, with decals already applied
(fuselage / wing, motor cover, canopy and cockpit)
- Separate EPO foam fins and fuselage nose-cone
3
- Control surface linkage hardware pack
- Factory-fitted 50 mm Ø ducted fan unit
- Factory-fitted brushless motor and speed controller
- 2 x factory-installed robbe E-COLINE 8G servos
- Multi-lingual assembly instructions
Replacement parts list
Order No.
25800001
25800002
25800003
26000001
8629
Figs. 1 and 2
- Glue the fins in place, lining them up accurately
Figs. 3 and 4
No. 5062 - Glue the nosecone to the fuselage.
No. 5020
Fig. 5
- Installing the receiver: connect the servos and the speed con-
troller to the receiver, referring to the RC system instructions for
the correct channel assignment and connector pin configuration.
Order No. (the orange signal wire corresponds to the white wire used for
robbe-Futaba systems).
F 4106 - Place the receiver in the fuselage and deploy the receiver
4548 aerial(s).
6911 or
6910
Fig. 6
-
Slide some heat shrink pieces onto each battery lead. Solder the
8895
socket according to figure and insulate the solder joint with heat
5151
shrink tubing.
Important: Do not reverse the connections of the battery to
8564
the speed controller. Reversing the polarity will destroy the
F1415
controller immediately.
8881
1713
Fig. 7 and 8
Sender = Transmitter
ON = ON
Motor aus = Motor "stopped
No.
2580
Description
Ducted fan unit 50 mm Ø
Brushless motor
Cabin
E-COLINE Servo 8G
BL controller ROXXY® Control 930