Rinsing The Coffee System - Krups EA870810 Intuition Manual De Instrucciones

Important:
The coffee grounds collector has enough capacity for about 9 coffee portions; not
regularly emptying the coffee grounds container and drip tray as indicated above
can damage your machine.
MAINTENANCE OF WATER TANK AND COFFEE BEAN
CONTAINER
For the preservation of best coffee flavor impacted by the quality of the water and hygienic
reasons, we advise you to use only fresh water and to daily clean the water tank with hot
water and a bottle brush.
Coffee beans can leave greasy residue on the tank that can affect the quality of the coffee.
For the preservation of best coffee flavor and hygienic reasons we recommend you to wipe
it with a dry, soft cloth each time it needs to be refilled.
Important:
Do not clean with water, the presence of water in the bean hopper could damage
the machine
It is recommended that you let it air dry before you put it back in the appliance

Rinsing the coffee system

This function is available at any time, unless the machine requires other maintenance.
– Place a container under the coffee nozzles.
– Switch on your machine then press
– Select the rinse function .
Press to start rinsing.
For hygienic reasons, it is recommended to rinse the coffee system daily or when not used
for a longer period (more than 2 days).
This function can be automatically done on start up. For more information, please refer to
"OTHER FUNCTIONS"
Full automatic cleaning program for the machine, 3 times a
year (approximately 13 minutes)
For the preservation of best coffee flavor and hygienic reasons we recommend you to clean
the coffee system 3 times a year.
For this cleaning you will need:
– 1 KRUPS cleaning tablet
– 1 container of at least 600 ml
The cycle will link two phases:
– 1 cleaning phase
– 1 rinsing phase
When do I run this program?
When it is necessary to run a cleaning program, the appliance notifies you.
When the machine is switched on, the "alert" LED
light up. See 11 – AUTOMATIC COFFEE SYSTEM CLEANING PROGRAM, fig 1 to 27.
42
.
and the LED on the interface will
– You can also start a cleaning cycle when you wish: by pressing
cleaning program, indicated by the LED
SYSTEM CLEANING PROGRAM, fig 1 to 27.
Important:
You do not have to run the cleaning program as soon as the appliance requests
it, but you must do it reasonably soon after. If cleaning is postponed, the alert
message will remain displayed as long as the operation has not been performed.
Important:
if you unplug your machine during cleaning or in the event of electrical failure,
the cleaning program will resume the current step at the time of the incident.
It will not be possible to postpone this operation: rinsing the water circuit is
mandatory. In this case a new cleaning tablet may be necessary.
Automatic descaling program (approximately 20 minutes)
Descaling your machine ensures its proper functioning and eliminates any deposit of
limescale or tartar.
Caution: If your appliance is equipped with our Claris Aqua Filter System cartridge
please remove it before the descaling procedure (see "Removing the Claris Aqua
Filter System cartridge").
To perform this cleaning you will need:
– 1 dose of KRUPS descaler
– 1 container of at least 600 ml
The cycle will link three phases:
– 1 descaling phase
– 1st rinsing phase
– 2nd rinsing phase
When do I run this program?
The appliance notifies you when it is necessary to run a descaling program.
Descaling your machine ensures it proper functioning and eliminate any deposit of limescale or
tartar This step is very important to ensure the proper functioning and longevity of your appliance.
When the machine is switched on, the "alert" LED
light up. Then, refer to section 12 – AUTOMATIC DESCALING PROGRAM, fig 1 to 30.
Important:
The machine lets you know when it is necessary to do so. However, you can start
descaling the machine at any time by pressing
The Claris Aqua Filter System cartridge
Installation:
– Remove the water tank and empty it. If necessary, remove the used filter cartridge.
– Turn the grey ring located on the upper end of the filter cartridge until it displays the
current date. The cartridge must be changed every 2 months.
– Screw the new filter cartridge into the bottom of the water tank using the accessory
supplied with the cartridge.
– Fill the water tank and put it back in place.
– Switch on the machine by pressing ON/OFF.
– Place an empty container under the coffee nozzles.
and selecting the
. Then see 11 – AUTOMATIC COFFEE
and the LED on the interface will
and selecting .
43