Intended Conditions Of Use; Optional Accessories; Maintenance And Cleaning; Changing The Saw Blade - Virutex TM33W Manual De Instrucciones

Ensure that the moving arm is well secured
in position when mitering.
7.5 SPECIAL CUTS 200 x 45 mm
In the 0°x0° position this machine can make cuts up to 200
x 45 mm. For these cuts must be placed on the lower table
to do this, just fit supplements N2 ref. 3346388 supplements
for 200 mm cuts (optional accessory) to the bottom table
and then the cut can be made as normal. This is possible due
to the retractable saw protector R (Fig. 16) which retracts
as the cut is made.
7.6 MULTIPLE CUTS
To make multiple cuts the length stop A1 must be installed
and regulated to the required measurement (Fig. 5)
8. CUTS ON THE UPPER TABLE,

INTENDED CONDITIONS OF USE

(only with models TM33W)
The laser guide also includes an On/Off
switch T1 (Fig. 22) to activate or deactivate
it. The switch must be turned to 'Off' for
cutting on the upper table.
On the upper table only plastics and wood
can be cut, never aluminium or angles.
To use the machine in this cutting mode the lower cover K1
(Fig. 6) should be positioned on the machine which prevents
any accidental contact of the saw disc under the table. Fit
the right-hand side of the fairing onto the machine first,
followed by the left-hand side. Once both parts are fitted on,
proceed to join them using closure clamps D1 (Fig. 6). Then
lock the machine in its transporting position using catch
B (Fig. 6), checking that the cover is perfectly in place and
fixed. Release knob A and lower the handle (Fig. 8). Release
knob L, withdraw the upper aluminium angle which covers
the blade protector and use it as a lateral cutting guide,
locking it again at the required distance from the saw (Fig.
11), this protector has a side slot that includes two nuts E4
(Fig. 11) designed to lock the wooden fillet that extends
up to the vertical axis of the centre of the saw blade. Pla-
cing this wooden fillet (Fig. 17) is necessary when making
short cuts (dowels or stocks). This is because in this type of
cutting, when the cut piece is ejected from the centre of
the leaf, if it lacks space in coming out, the turning of the
blade, which could cause the accidental expulsion of the
part, will retain it.
The exit position of the saw with respect to the table is
regulated by releasing knobs M (Fig. 1) and placing the table
at the required cutting height, using the height adjustment
knob M2, ensuring that the blade overhangs the material to
be cut only at the level of the tooth, tighten up the knobs
at the selected height.
Lock button E1 in place for cutting with a raised table (Fig. 8).
Once the cutting work on the table is finished replace the
aluminium angle in the protection position before using
the machine as a mitre saw again.
Do not use the upper table without putting
the lower protecting cover in position.
Never work without the upper protector.
Use push stick E5 supplied with this machine
to feed in the part to the saw blade (Fig.
21). The machine is equipped on one of the
sides of the upper table with two fastening
supports with which to attach the E5 thrust
rod during transport.
Use the upper protector of the upper blade
correctly.
Ensure that the tilting arm is well secured in
position when working on the upper table.
9. DUST COLLECTION OUTLET
On the rear of this machine there is a Ø 38 mm dust collection
outlet, where it is possible to connect up a flexible tube,
adapting an industrial aspirator or any system of centralised
aspiration for collecting dust and shavings. We recommend
connection to our aspirators AS182K, AS282K.
For work on the upper table, and in addition to the connection
mentioned above, the fairing is provided with a nozzle D2
(Fig. 6) to which the standard dust collector attachment (Ref.
6446073 3.5 m / Ref. 1746245 5 m) must be connected for
perfect collection of the shavings.
We recommend you keep the machine permanently con-
nected to a dust and shavings collection system.

10. OPTIONAL ACCESSORIES

Ref. 3345416 Set of two pressers (Fig. 20). It is indispensable
for cutting aluminium and plastic profiles.
Ref. 3345470 Set of side handles (Fig. 19)
Ref. 7246098 Square for upper table
Ref. 5800100 Movable working table MT58K (Fig. 29)
Ref. 8200100 Aspirator AS182K
Ref. 8200200 Aspirator AS282K

11. MAINTENANCE AND CLEANING

Ensure that the machine is disconnected
from the mains before carrying out any of
these operations.

11.1 CHANGING THE SAW BLADE

Release knobs M (Fig. 1) and raise the table to its maximum
position. Then, press button O and slowly turn the saw until
it is locked (Fig. 1). Next, release screw P (Fig. 12) clockwise
using the service key supplied. Once the saw blade is released
move it upwards and then remove it down through the
side of the head of the machine, avoiding the protector.
11