YATO YT-82814 Manual Original página 16

GB
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply plug from the mains.
In addition, you should clean the battery and its terminals of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. When you press the button, LEDs will light up (V), the more LEDs will light up, the more
fully the battery pack is charged. If the button is pressed and the LEDs are off it means that the battery is discharged.
Disconnect the battery from the tool.
Push the battery in the charger socket (V).
Plug the charger into a mains socket.
When the red LED lights up, it means the loading process.
When charging is complete, the red LED goes off , and green LED lights up, indicating a full charge of the battery.
Unplug the charger from the mains outlet.
Remove the battery from the charging station, by pressing the battery latch button.
Attention! If, when the charger is connected to the power supply, the green LED is on, this indicates a fully charged battery. In this
case, the charger does not start charging.
Mounting and replacing of the saw blade (II)
You should check whether the blade is not damaged, cracked, whether the cutting teeth are not broken, etc. In the case of dam-
age, replace the saw blade for a new one.
Saw blades diff er depending on their assignation. Saw blades for wood and wood-based materials have widely spaced teeth and
saw blades for metal and plastic have fi ner teeth. You should select a saw blade suitable for the planned work. You can mount the
saw blade with their teeth directed to the lower or upper part of the housing.
Attention! Mounting the saw blade should be carried out in the protective gloves. This will reduce the risk of injury.
Rotate the spindle and insert the blade holder in the spindle gap. Rotate the clamp to the opposite side and make sure that the
blade has been properly fi xed: when the clamp is in its original position, the saw blade can not be removed from the spindle.
Setting the height and angle of the foot (III)
By setting the foot height you can adjust the cutting height. To do this, you must rotate clockwise the lever located on the front
panel, set foot on the desired height, and turn the lever counterclockwise, until its location is locked in the position by a latch. Make
sure, that the foot will change its height during operation. Adjusting the foot is possible in a gradual way.
The foot allows smooth for adjustment of skid angle, to do this, you must lean it against the foot guide. This will allow you to change
the cutting angle without taking the foot from the surface of the cut material.
OPERATING OF THE TOOL
Before every operation, you should ensure that the blade is not damaged and that it is mounted correctly. Wear eye protection,
hearing protectors and working gloves. Mount the workpiece to the workstation, for example by using carpentry clamps, vice, etc.
Never hold the cut material only by hands or other parts of the body. In the case of cutting you must support the material at its ends
and near the cut line. Supports must be placed on both sides of the cut line so during cutting, the blade would not jammed in the
cut kerf. During cutting the foot must be supported by its whole surface of the base of the cut material.
Switching on & off of the device
You should make sure that at the work place the surface is even, stable and free of pollution.
Adopt a stable stand.
Grab the tool by the handle. You should not rest any parts of the working tools on any subject or object.
Push and hold the blocking of the switch, press the your fi nger and hold it in this position. Check whether the saw blade is mov-
ing freely, and the tool does not suspiciously or excessively vibrate, it is thus not emit smoke or a strange smell. If you notice
any deviations from that correct operation, you should turn off the tool, remove the plug from the mains and take the tool to an
authorized repair point.
During operation it is not necessary to hold the switch blockade.
The tool is stopped after releasing the pressure on the switch. After switching of, the saw blade can move for some time.
Cutting wood (VI)
Before you start cutting, you should draw the cut line with a carpentry pencil. Then rest the tool on its foot and set the saw blade
according to the drawn line, then turn on the tool, allow the tool to reach the rated speed and start cutting. At the time of cutting do
not exert too much pressure on the foot and the blade, as this can cause rupture of the working tool.
Plunge cutting
Attention! Plunge cutting may be carried out only in soft materials such as the soft wood or gypsum. You should never make
O R I G I N A L I N S T R U C T I O N S
16