SBS BF400 Instrucciones página 2

G G B B
Thank you for choosing the SBS BF400
Bluetooth earpiece. Before using it for the first
time, follow the instructions printed below.
V V O O L L U U M M E E ( ( + + ) )
L L E E D D
V V O O L L U U M M E E ( ( - - ) )
C C H H A A R R G G I I N N G G T T H H E E B B A A T T T T E E R R Y Y O O F F T T H H E E E E A A R R P P I I E E C C E E
The earpiece uses a battery with high
performance "Lithium Polymer" technology.
The first time you use the earpiece, the battery
inside may not be charged and it will be
necessary to charge it up.
R R e e c c h h a a r r g g e e . . Connect the battery recharger to
the electric socket and to the earpiece. The
red light will come on and the recharging
process will begin. When the battery has been
recharged the light will go off. It will take
about two hours to fully recharge the battery.
B B a a t t t t e e r r y y d d e e a a d d . . When the BF400 battery has
almost run down, the light will flash red and a
beep will be heard in the earpiece.
N N O O T T E E : : to extend the life of the battery, we
recommend that you leave the BF400
switched off while recharging and only
recharge it when it is dead. If the BF400 has
not been used for some time, it may take a
few minutes for the red light to come on.
S S t t a a t t u u s s L L E E D D
Stand-by Flashing BLUE
"Find me" mode Flashing RED/BLUE
Calling Quick flashing BLUE
Battery dead Slow flashing RED
Recharge Fixed RED
All manuals and user guides at all-guides.com
S S W W I I T T C C H H I I N N G G O O N N , , C C O O N N N N E E C C T T I I N N G G A A N N D D
S S W W I I T T C C H H I I N N G G O O F F F F T T H H E E E E A A R R P P I I E E C C E E
S S w w i i t t c c h h i i n n g g o o n n . .
M M U U L L T T I I F F U U N N C C T T I I O O N N
Press the multifunction button and keep it
B B U U T T T T O O N N
pressed until the blue light flashes three times
(about 3 seconds). The BF400 will switch to
stand by.
C C o o n n n n e e c c t t i i n n g g . . After switching on the BF400,
briefly press the multifunction button to
M M I I C C R R O O P P H H O O N N E E
connect the earpiece to the last device with
which it has been associated (only after
making the association).
E E A A R R P P H H O O N N E E
S S w w i i t t c c h h i i n n g g o o f f f f . . Press the multifunction button
and keep it pressed until the red light flashes
three times (about 3 seconds).
A A S S S S O O C C I I A A T T I I O O N N O O F F T T H H E E E E A A R R P P I I E E C C E E W W I I T T H H A A
B B L L U U E E T T O O O O T T H H D D E E V V I I C C E E
Before using the Bluetooth headset, you must
associate it with the device you are going to
use it with (telephone/PC).
A A S S S S O O C C I I A A T T I I O O N N
• Ensure that the BF400 is switched off. Press
• Run the search for new Bluetooth
• Select the BF400 and, when requested to do
• The phone/PC will tell you that the new
N N O O T T E E : : With some phones it might be
* * To make the association, follow the
the multifunction button and keep it pressed
until the light starts flashing red/blue (about
6 seconds), in this way the earpiece is ready
to be picked up by other devices ( "find me"
mode).
accessories from your device (phone/PC)* * .
At the end of the search the name of our
earpiece will appear on the display (the
name may vary from device to device).
so, enter the PIN 0000, then press "OK" .
bluetooth device has been associated, while
the BF400 light will flash blue ( stand-by ).
necessary to authorise connection
from the phone.
instructions in the user manual supplied
with the phone or with the PC Bluetooth
B B F F 4 4 0 0 0 0