Publicidad
Idiomas disponibles
Idiomas disponibles
Should the circuit breaker trip repeatedly then the most
probable causes are:
-Abnormal working conditions,
-Treadmill belt in need of lubricant,
-Solvent based lubricants used (use BH type),
- Belt is too tight.
Plug the unit into a wall socket with an EARTH terminal.
Set switch (L) to Position [1].
ASSEMBLY INSTRUCTIONS.-
Take the unit out of the box and place it on the floor as
shown in Fig.0.
The assistance of a second person is advisable for
the assembly work.
Make sure that all of the pieces are there:
(1)
Main structure.
(3)
Side bar (left).
(4)
Side bar (right).
(5)
Monitor support.
(156) Bottle of lubricant.
(A)
MP3 wire.
(48) Screw M8x20.
Wrenches.
Follow the instructions step by step to assemble:
1. FITTING THE SIDE BARS.-
At least two people are needed to assemble the machine
This will avoid any possible accidents.
First loosen off screws on the motor cover (18) and
remove the cover (18), Fig.1.
2.
Then slightly screw the left side bar (3) to the structure
using the screws (48), Fig.2.
3.
Then place the right side bar (4), Fig.2, close to the
main structure and connect the wires. Then slightly screw
the right side bar (4) to the structure using the screws
(48).
4. ATTACHING THE MONITOR TUBE.-
Take hold of the handrail (5) and connect the cables with
wires sticking up out of the handlebar, Fig.3.
Once this is done, rest the handrail handlebar on top of
the focus bars, making sure not to catch any of the cables.
Now tighten slightly using the screws (48), Fig.3.
5. FITTING THE MOTOR COVER.-
Position the motor cover (18) on the machine, Fig.4, fit
and tighten with the previously removed screws, Fig.4.
Tighten the screws of the previous steps.
Fig.B
MOVEMENT & STORAGE.-
The unit is equipped with wheels (35), Fig.5 to make it
easier to move. Make sure that the mains cable is
unplugged from the wall socket.
To prevent accidents DO NOT move the treadmill across
uneven floors.
MAINTENANCE.-
Use the bottle of lubricant (156) to lubricate the inside of
the belt Fig.6 in order to keep your unit in top condition
and to ensure that friction between the belt and the board
is kept to a minimum (due to different running styles,
always apply more lubrication to the area where you place
your feet during the exercise).
It is advisable to lubricate the base of the belt between the
board and the band depending on how often it is used.
<6
6-12
>12
Note: This preventive maintenance schedule is only
meant for home use.
It is suggested to maintain the unit every month for
commercial use.
If the belt starts to slip after lubrication, then check the
tension of the belt. To tension the belt, take the 6mm Allen
key and with the machine set to 4km/h turn screws (R & L)
one turn in a clockwise direction.
ADJUSTING THE BELT.-
If your unit is not seated evenly on the four contact points,
this may cause the belt (X) to shift sideways. Rigorous
quality control adjusts and checks the running belt.
However, due to weight differences and individual styles
.
of running, the belt may be prone to shift sideways. If the
belt does shift to the left or right, stop the machine.
BELT OFFSET TO THE RIGHT.-
This procedure is very important. Follow these steps. In
order to adjust the belt, set the unit in motion at a speed of
4km/h.
If the belt has moved to the right, turn screw (R) on the
right-hand side of the machine a 1⁄4 turn clockwise. Note
the position of the belt, if after one minute the belt is not
completely centred then repeat the operation. If you see
that the belt has moved too far over to the left then turn
the right screw back slightly in an anticlockwise direction
Fig.7.
As soon as you have adjusted the belt you can begin
exercising again.
BELT OFFSET TO THE LEFT.-
In the event that the belt has moved to the left, turn screw
(L) on the left-hand side of the machine a 1⁄4 turn
clockwise. Note the position of the belt, if after one minute
the belt is not completely centred then repeat the
operation. If you see that the belt has moved too far over
to the right then turn the left screw back slightly in an
anticlockwise direction Fig.7.
Important: Overtightening of the belt can lead to a loss of
speed on the machine and even stretch the belt itself.
11
Hours per week
<3
3-7
1 year
6 months
6 months
3 months
3 months
2 months
>7
3 months
2 months
1 month
Publicidad
