Rollplay BMW X5 Instrucciones De Montaje página 8

The BMW trademarks are used under license from BMW AG. BMW name
and associated logos are trademarks of BMW AG.
Forward and reverse gears.
Multi-functional steering wheel with different sound effects.
Two working doors
With working LED headlight
Quick release wheels
With real door handle latches
19. Protective equipment should be worn
20. Exhausted batteries are to be removed from the toy.
21. Rechargeable batteries are to be removed from the toy before being
charged.
/ /
@
1. Assemble the front wheel: (Fig.1)
Slide the washer onto the front axle (A). Slide the front wheel
Font wheels onto the front axle.Push on the center of the wheel (B) and
snap it into place.Gently pull the wheel to ensure that it is secure. If
wheel comes loose,then repeat the first three steps.Repeat steps 1-3
for the remaining front wheel.
2. Assemble the rear wheel: (Fig.2)
Slide the rear wheel with the gear teeth facing inward onto
the rear axle (A).Line up the gear teeth on the wheel with the grooves
on the gear box (8).Push on the center of the wheel and snap it into
place.Gently pull on the rear wheel to ensure that it is securely attached
to the axle.
3. Assemble the wing mirrors:(Fig.3)
Remove the screw (A) and nut (B) from the mirror Mirrors before
attaching.Insert the left side mirror Mirrors into the slot on the side of
the body.Push it into the slot.Insert the screw (A) and fasten the nut (B)
to secure the mirror.Repeat steps 1-3 for the right side mirror.
4. Assemble the steering wheel: (Fig.4)
Remove the screw and nut from the steering wheel assembly Steering
wheel before attaching.Plug the steering wheel connector (A) into the
dashboard connector (B).Insert the steering wheel Steering wheel into
the steering rod, and match the screw holes of the steering wheel and
the steering rod.Insert the screw into the hole and fasten the nut to
secure.
5. Connect the power: (Fig.5)
Connect the connector on the battery with the connector of the driving
box.
6. Assemble the seat:(Fig.6)
Position the seat Seat over the battery compartment Click in the
hook on the back of the chair into the empty slot on the car body.Turn
the thumb screw clockwise on the seat to lock it properly into position.
*
)
Operation Instruction:
A. Forward and reverse
To turn on the vehicle, turn the power switch to "I." To turn off the
vehicle, turn the power switch to "O."Push the shifter forward to move
forward. Pull the shifter backward to go in reverse.Press the foot pedal
down to go. Release the foot pedal to stop.(Fig.A)
Insert the MP3 cable into the MP3 jack and connect to your device.
Turn the MP3 on by rotating the on/off dial. To adjust the volume,
rotate the dial.
Turn on the radio by rotating the dial switch, to tune the radio, press
'Reset' and 'Tuning' button.
Press the left and right steering wheel buttons for horn and engine
sounds
Battery power indicator: Press the power indicator button to check
battery level.
• Three Lights: Battery is fully charged
• Two Lights: Battery level is low
• One Light: Battery power is lower than 9.5V, and the battery must be
recharged
Turn off automatically function:
The car will be power off automatically after turn on 2 hours, and the
car without any function. Turn on the power switch to restart the car
and functions are normal.
B. Steering wheel function(Fig. B)
Press the left and right buttons on the steering wheel to make
sounds.Note: The steering wheel connector must be attached to the
dashboard connector to make sounds. (Fig.B)
C. Door use
Pull the handle out, the door bolt automatically indent,
and the door will be opened. Pushing the door slightly, and the door
will be closed.
D. Operation of Remote Control: (Fig.D)
1. Press the "Forward" button, the vehicle moves forward; press the
"Backward" button, the vehicle runs backwards. Speed is up to the gear
set by the remote control.
2. The "Speed" button is the speed control button, it can be set three
speeds. Press the button to choose the corresponding speed. LED
displays speed synchronously, full light when the speed is the fastest, a
light when the speed is the slowest.
3. Press the "Left" button, the vehicle returns left; press "Right" button,
the vehicle returns right.
4. Press the "Stop" button to stop the vehicle, while the LED shows a
flow. Then press other buttons on the remote control, the vehicle
reruns according to the button function.
5. The vehicle has soft start and soft stop function.
6. When the remote control has no operation for more than 5 seconds,
it will enter into the hibernation (power-saving) mode,
7. The vehicle will be shut down automatically without operation for 2
hours.
E. Code Remote Control with E-Car: (Fig.E)
Press the forward, backward and speed control buttons at the same
time. LED lights flashing showed the state into the code. Now press the
power switch in 5 seconds, automatic code will be completed and LED
lights are restored to normally bright state. State recovery will be
closed automatically without operation for 5S. If the code fails, please
repeat the above steps.
7
( )
(