Setup And Special Configurations - Midland BTX2 PRO Manual De Instrucciones

Enabling:
› Follow the same procedure up described; now the blue LED will flash once.
To exit the "Setup" mode, double click the "Middle" button.
FM Radio with intercom
When you are in "FM Radio" mode is not possible to manually open the intercom, you
can only open it using VOX feature (just talk) to the unit paired on the "Middle" button.
To manually activate the intercom you must switch to "Intercom" mode.

Setup and special configurations

Resetting all paired devices
Sometimes you may find it necessary to delete all the pairing references stored in the
Midland BTX2 PRO unit (reset operation).
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button 7 sec., until the Red light is on permanently.
› Then simultaneously press and hold down the "Volume +" and "Volume –" buttons
for 3 seconds. The Blue Light will be lit on for 1 sec and than back to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode.
This procedure deletes all the paired Bluetooth devices stored in the memory and it is
therefore possible to start a new "clean" pairing session.
Back to factory setting
Sometimes you may find it necessary to go back to the factory setting, to reset all the
changes/setup already made and have a "clean" unit.
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Then simultaneously press and hold down all the three buttons "Forward"-"Midd-
le"-"Backward" for 3 seconds. The Blue Light will be lit on for 1 sec and than back
to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the Midland
BTX2 PRO
www.midlandeurope.com
All manuals and user guides at all-guides.com
Adjusting/ Disabling the VOX feature (Intercom and telephone)
The Intercom feature can be enabled both manually and vocally (VOX). The VOX acti-
vation is influenced by the helmet type, the background noise and therefore by the
speed.
For optimum results, it is possible to choose one of the following four microphone sen-
sitivity levels: high, medium, low and very low. The default setting of Midland BTX2
PRO is "High". It is also possible to disable the VOX feature in order to activate the
Intercom and phone call answering features in manual mode only.
Adjusting the sensitivity of the (VOX)
To perform this operation you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
3. Your Midland BTX2 PRO is now in "Set up mode".
4. Press the "Backward" button shortly and the red light changes to a steady blue.
5. Now, press "Volume +" or "Volume -" to increase or reduce sensitivity. Every time
6. Press again the "Backward" button shortly; the Blue light will flash several times, in
7. If needed, you can adjust again the sensitivity repeating the steps from point 1,
Disabling the VOX feature (Intercom and telephone)
Follow all the procedure described in the previous steps and choose the option of only
one flash (VOX disabled).
manently.
you press the Volume buttons the RED light will flash for confirmation. When you
reach the end of the upper and lower limit, the RED light will not flash.
order to let you know the selected sensitivity:
One flash = VOX disabled
Twice = low sensitivity
3 times= normal sensitivity
4 times= high sensitivity (default setting)
5 times = Highest sensitivity
The light indicator is now back to steady RED ("Set up mode") and the changes are
confirmed
otherwise exit the Setting mode by double clicking the "Middle" button. Once the
red light turns off, the blue led starts blinking. Now you can use your Midland BTX2
PRO
13