Talk 2 All - Universal Intercom With Different Brand Unit - Midland BTX2 PRO Manual De Instrucciones

Activate Conference mode
In "Intercom Mode" and no active audio, keep pressed the FWD and Middle buttons for
3 sec. The voice announcement "Conference" will tell you that it is active.
When the Conference mode is active the "Phone" mode is not available because all the
devices paired on Vol+ and Vol – are temporary disconnected to guarantee the stability
of the conference mode.
Disable the "conference" mode
The conference mode can be disabled in every moment, just pressing the FWD and
Middle buttons for 3 sec. You will hear the voice announcement "Intercom" and from
that moment your Midland BTX2 PRO will start working with "one to one" intercom
and all the devices paired on Vol+ and Vol- are back, together with the "Phone" mode
and the "Talk2All-Universal intercom" feature.
Attention: when the "conference" mode is active, the "Talk2All- Universal Intercom" (to talk
with not Midland brand intercom) is not available.
Also if one unit was paired on the CTRL (middle) button, it is temporary unavailable,
you need to disable the "Conference" mode and go back to the standard "one to one"
Intercom mode.
How to use the conference mode
When the conference mode is active, is possible to open the intercom communication
pressing both the FWD and BWD button. One click on the button will open the inter-
com communication, one click on the same button will close it.
The two units that are in the middle of the chain (unit 2 and 3) must keep the intercom
open on both FWD and BWD button to allow the full communication of the four units
together.
"One Click Talk" function
When the conference mode is active, it is possible to open the intercom communica-
tion to all the 4 users just in "one click". Press short the CTRL (middle) button and you
will automatically open the conference to all the unit connected.
8
All manuals and user guides at all-guides.com

Talk 2 All - Universal Intercom with different brand unit.

Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to pair your
Midland BTX2 PRO to a different brand intercom available on the market.
You can pair a not Midland Intercom on the "Forward" button.
› On the Midland BTX2 PRO enter the setup mode: (with the unit OFF press and
› Keep pressed the "Forward" button for 7 seconds: the Red and Blu LED light will
On the other intercom (not Midland brand) follow the procedure to pair to a phone,
because the BTX2 PRO is paired as a Phone. If successfully paired the red/blue light
will stop flashing and the blu light will slowly flash instead.
Attention: remember to switch OFF all the other Bluetooth devices during the pairing pro-
cedure, only the two devices involved in the pairing must be turned on.
To open/close the "Universal Intercom" communication on the Midland
BTX2 PRO press very long (7 sec) in "Intercom" mode the Forward but-
ton. On the other intercom just press the phone redial or voice dial button.
Maybe it will be necessary to press the redial button two times, depending on the model
of the not Midland intercom.
Attention: In order to use the the "Talk2All-Universal Intercom" feature the pairing on the
other unit must be done as a phone. The other intercom (not Midland brand) will be able to
be paired to a phone only if two phones are supported.
You can pair also a Midland unit as Talk2All, that means the pairing must be done as a
phone (one unit use the Talk2All procedure and the other unit use the pairing to "Phone"
procedure).
hold down the Middle button about 7 sec. until the Red light is on permanently).
start flashing fast, then (while you still keep the button pressed) the Red and Blu
LED lights will change to slow flashing. Now you can stop pressing the button.
Talk2All - Universal Intercom
Not Midland Unit
www.midlandeurope.com