Package Contents; Description Of Parts; How To Use - Patron PBH-300 Manual Del Usuario

English
PBH-300
CE Compliance Information
Partron headset hereby declares that this PBH-300 is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
FCC Compliance Information
FCC ID : 2AD5K-PBH300
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference received,
including interference that may cause undesired operation.
Information to the user:
NOTE : This equipment has been tested and found to comply with limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation. If this equipment causes
harmful interference to radio or television reception can be determined by turning the equipment off and on.
The user is encouraged to try the correct interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION TO USER : Changes or modifications not expressly approved by the party reasonable for compliance could void
the user's authority to operate the equipment.
Contents
PBH-300 User Manual

/ Package Contents /

Cable Clip
Earbud Covers
(Small / Large)
Quick Manual

/ Description of Parts /

Mic 1
Micro USB
Mic 2
/ Installation of Cable Clip /
Please hang the clip on the
headset band by opening
it a little bit.
※ The length of the cable can be easily adjusted by using the clip.
/ Product Specifications and features /
Standby Time
Operating Time (Music)
Operating Time(Call)
Charging Time
Battery
Working Distance
Supported profiles
Decoder
Bluetooth Version
Power Consumption
※ Above mentioned operating times based on connected devices or surrounding
environment.

/ How to use /

1. Power On / Off
Power On
- Press the call button for 1 second
- The red and blue LED light flashes for 0.5 seconds and a voice guide announces
that the power is turned on.
Power Off
- Press the call button for 3 seconds
- The red and blue LED light flashes for 0.5 seconds and a voice guide announces
that the power is turned off.
2. Battery Charging
LED indicator
- When the charger is connected, the Red LED is on.
- When charging is completed, the Blue LED is on.
※ When the charger is connected, the headset will be disconnected from the device.
※ The power turns off when the USB charger gets disconnected.
Recommendations
- Using an USB Hub may take extra charging time due to the low current.
For fast charging, please use a 5V 500mA ~ 5V 1A rated charger.
※ It takes approximately 2 hours to charge the device if the battery is totally empty.
3. Battery Status Alarm & Alert
- Press Call and Volume + button at the same time for a second for audio
guidance about the current battery level.
"Battery Full" / "Battery Half" / "Battery not enough"
4. Low Battery Alarm & Alert
- The red LED light flashes 3 times with the vocal guidance "Battery not enough" if the
battery will not last longer than one hour.
5. Critical Battery
- The notice continues every 2 minutes if the battery will not last longer than 10 minutes and
power is turn off with voice guidance "Battery Empty" at the critical battery state.
6. Pairing
Before using the headset for the first time, you must pair it with a Bluetooth-enabled device.
* Pairing: Connecting Bluetooth-enabled device and headset.
- Press the call button for 1 second to turn on the device
- Once the power is on, the headset will automatically enter pairing mode.
(The red/blue LED light flashes)
- The headset will automatically enter the waiting mode if it is not connected within 3 minutes.
(The power is automatically turned off after 50 minutes in waiting mode)
- On the device you want to have paired, find the Bluetooth menu and search & select
"PBH-300" from the list of nearby Headsets.
- If connected without any problem, the headset will be paired accompanied by the audio
guide "Connected"
- Once the pairing is complete, the devices will be automatically paired afterwards.
※ Manual Pairing
- Press and hold the "call" button for 2 seconds to turn the device on.
It will automatically enter pairing mode with the voice guide "start pairing".
Scan for the PBH-300 and tap on it to connect.
- If PIN code is required, please enter "0000".
Clearing Paired Device
- Hold call button and Volume - button for 1 second after having turned off the Bluetooth of your
mobile devices. Previously established connections will be deleted with the voice guide
"Clear paired list", and the device will enter pairing mode.
7. Calling
Voice Dial
- Briefly press the Call button to activate Voice Dial.
※ To use Voice Dialing, your mobile phone must support this function.
8. Call Answer / Call End / Call Reject
Call Answer / Call End
- Briefly press the Call button to answer the incoming call.
- Briefly press the Call button to end the call.
Call Reject
- Press and hold the Call button to reject the incoming call.
9. Call Transfer
- During the call, press the Call button for 1 second. The audio will be transferred
from headset to mobile phone.
- Press Call button for 1 second again. The audio will be transferred from mobile phone
to headset.
10. Setting Waiting Mode while Calling
Setting Waiting mode
- During the call, briefly press Call button twice to put the call on hold.
Press Call button twice again to return to the call.
※ To put the call on hold, your mobile phone must support this function.
Incoming second call while calling
- Briefly press Call button to end the original call and answer the second call.
- Briefly press Call button twice to answer the second call without hanging up the
original call (Original call will be put on hold)
Ending a Call
- Briefly press the Call button.
Package Contents
Description of Parts
Installation of Cable Clip
Product Specifications and Features
How to use
Power on/off
Charging
Pairing
Calling
Transferring a Call
Volume Control
Music Play
Change language settings
Multi-Connection
Using Partron Reader Application
Button Functions and Status Information
Precautions
Product Warranty and Service
Limited Warranty
Product Warranty Certificate
※ The components of the package are subject to
change without notice to improve the product
performance or quality.
Portable Pouch
Charging Cable
Place it in a suitable position and
fix the earphone cable properly.
600 hours
15 hours
15 hours
2 hours
Lithium Polymer Battery 3.7V (210mAh)
10m
HFP / HSP / A2DP / AVRCP
SBC, APT-X
Version 4.1
0.5W
PBH-300
Volume Up
Volume Down
LED
Play / Pause
Call
14
14
15
16
17