The tool continues to rotate after some second it is
turned off.
SPEED ADJUSTMENT
The speed can be adjusted in two ways: by means of the
variable actuation switch (2), by means of the adjustment
wheel fitted on the upper part of the machine (3)
Adjustment by means of the wheel (3) affects the adjustment
made using the variable actuation switch (9), determining the
maximum speed of the motor.
The speed must be selected according to the characteristics of
the pads and those of the material to be machined.
ALLOWED ACCESSORIES
Polishing foam and foam support pad up to Ø 200 mm max.
NOISE/VIBRATION LEVEL
The equivalent noise pressure level and the mean squared
acceleration are measured according to standard:
EN 60745-2-3
SOUND
PRESSURE
UNCERTAINTY
LEVEL
[dB(A)]
[dB(A)]
L
pA
LH19E
85
Use ear protection!
Displayed emission values are comparative and are to
be employed for a provisional assessment of the
operator's risk exposure during the work period. Appropriate
evaluation of work period must also include tool's idle and stop
periods. These emission values represent the tool's main
applications. If the tool is used for other applications, with
other accessories, or if it does not undergo regular
maintenance, emission values can significantly increase during
operations.
MAINTENANCE
All maintenance operations are carried out with the power
supply disconnected.
At the end of each work session, or when required, remove any
dust from the body of the tool using a jet of compressed air,
paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by
the user.
Maintenance and cleaning of the inner parts, like brushes,
ball bearings, gears etc. or others, must be carried out only
by an authorized customer-service workshop also available
on the website http://www.rupes.it under Service section. Use
exclusively original RUPES.
VIBRATION LEVEL[m/s
SOUND
(polishing)
POWER
LEVEL
On 3 AXIS
K
L
a
wA
h
3
96
2,50
p
DISPOSAL (WEEE DIRECTIVE)
For EC countries only: According to the European
Directive on Waste from electrical and electronic
equipment and its implementation in conformity with
national standards, exhausted electrical equipment must be
collected separately, in order to be recycled in an
environmentally friendly way. The product, when it reaches the
end of its life, must not be dispersed in the environment or
thrown away as household waste. It must be disposed at
authorized recycling centres (contact your local authorities to
know where to dispose of the product according to the law).
The correct disposal of the product contributes to the health
and preservation of the environment.
Illegal disposal of the product will entail penalties against the
offenders.
CONFORMITY DECLARATION
We declare on our responsibility that the represented tool is in
conformity with the Essential Requirements of Safety of the
following Directives:
2006/42/EU; 2014/35/EU; 2014/30/EU; 2011/65/EU.
]
2
The tests have been carried out in accordance with the
UNCERTAINTY
European Harmonised Standar:
K
EN 60745-1:2009 + A11:2010;
1,00
EN 60745-2-3:2011 + A2:2013 + A11:2014 + A12:2014
+ A13:2015;
EN 55014-1:2006 + A1:2009 + A2:2011;
EN 55014-2:1997 + A1: 2001 + A2:2008;
EN 61000-3-2:2006 + A1: 2009 + A2:2009;
EN 61000-3-3:2013;
EN 62233:2008.
THE PRESIDENT
Technical file at:
RUPES SpA
Via Marconi, 3A - Loc. Vermezzo
20071 VERMEZZO CON ZELO (MI) - Italy
S.p.A
G. Valentini
Vermezzo con Zelo (MI), 16/06/2017
9