Speed Adjustment; Conformity Declaration - Rupes LK900E Instrucciones De Uso

START AND STOPPING
- Starting: push the lever of the switch (2) towards the body
of the tool; if the tool is to be locked in the ON position,
press button (6) at the same time and keep it pressed while
releasing lever (2), thus locking the switch.
- Stopping: release the lever of the switch or, if locked in
position, push the lever to release the lock button.
The tool continues to rotate after it is turned off.
Do not empty the tool with the polishing pad still
mounted. In this way, the polishing pad may be subject
to lacerations

SPEED ADJUSTMENT

The speed can be adjusted in two ways: by means of the
variable actuation switch (2), by means of the adjustment
wheel fitted on the upper part of the machine (3)
Adjustment by means of the wheel (3) affects the adjustment
made using the variable actuation switch (2), determining the
maximum speed of the motor.
The speed must be selected according to the characteristics of
the pads and those of the material to be machined.
DISASSEMBLY OF ACCESSORIES
PLATE BASE
- Loosen the screws (12) and remove the plate base (8)
POLISHING FOAM
- Remove the polishing foam used and apply the new one with
pressing on the backing pad (8).
ALLOWED ACCESSORIES
LK900E: polishing foam Ø 180 mm for backing pad Ø 150 mm.
Polishing foam Ø 150 mm for backing pad Ø 125 mm optional.
NOISE/VIBRATION LEVEL
The equivalent noise pressure level and the mean squared
acceleration are measured according to standard:
EN 62841
SOUND
PRESSURE UNCERTAINTY
LEVEL [dB(A)]
[dB(A)]
L
pA
LK900E 84
Use ear protection!
Displayed emission values are comparative and are to be
employed for a provisional assessment of the operator's risk
exposure during the work period. Appropriate evaluation of
work period must also include tool's idle and stop periods.
These emission values represent the tool's main applications.
If the tool is used for other applications, with other accessories,
or if it does not undergo regular maintenance, emission values
can significantly increase during operations.
Danger! The indicated measurements refer to new
power tools. Daily usage causes the noise and vibration
values to change.
MAINTENANCE
All maintenance operations are carried out with the power
supply disconnected.
VIBRATION LEVEL[m/s
SOUND
(polishing)
POWER
LEVEL
On 3 AXIS
K L a
wA h
3 95 6,00
At the end of each work session, or when required, remove any
dust from the body of the tool using a jet of compressed air,
paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by
the user.
Maintenance and cleaning of the inner parts, like brushes, ball
bearings, gears etc. or others, must be carried out only by an
authorized customer-service workshop.
DISPOSAL (WEEE DIRECTIVE)
For EC countries only: According to the European
Directive on Waste from electrical and electronic
equipment and its implementation in conformity with
national standards, exhausted electrical equipment must be
collected separately, in order to be recycled in an
environmentally friendly way. The product, when it reaches the
end of its life, must not be dispersed in the environment or
thrown away as household waste. It must be disposed at
authorized recycling centres (contact your local authorities to
know where to dispose of the product according to the law).
The correct disposal of the product contributes to the health
and preservation of the environment.
Illegal disposal of the product will entail penalties against the
offenders.

CONFORMITY DECLARATION

We declare on our responsibility that the represented tool is in
conformity with the directives:
2006/42/CE, 2014/35/CE, 2014/30/CE, 2011/65/CE.
The tests have been carried out in accordance with standard:
EN 62841-1:2015
EN 62841-2-4:2014
EN 55014-1: 2006 + A1: 2009 + A2: 2011
EN 55014-2: 1997 + A1: 2001 + A2: 2008
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 62233: 2008
EN 50581:2012
]
2
THE PRESIDENT
UNCERTAINTY
K
2,00
Technical file at:
RUPES SpA
Via Marconi, 3A
20080 - Vermezzo (MI) - Italy
S.p.A
G. Valentini
Vermezzo (MI), 10/01/2018
7