Descargar Imprimir esta página

Nilfisk-Advance SelectGloss 1500 Instrucciones De Uso página 6

Publicidad

INTRODUCTION
This manual will help you get the most from your Kent SelectGloss™ 1500.
Read it thoroughly before operating the machine.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your Authorized Kent Service
Center, who employs factory trained service personnel, and maintains an
inventory of Kent original replacement parts and accessories.
Call the KENT DEALER named below for repair parts or service. Please specify
the Model and Serial Number when discussing your machine.
(Dealer, affix service sticker here.)
NAME PLATE
The Model Number and Serial Number of your machine are shown on the
Nameplate on the front of the motor and on top of the motor shroud under the
cover. This information is often needed when ordering repair parts for the
machine. Use the space below to note the Model Number and Serial Number of
your machine for future reference.
MODEL NUMBER
SERIAL NUMBER
UNCRATING
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected. Contact the Kent Customer Service Department immediately to file
a freight damage claim.
PREPARING THE FLOOR
Before each use of this machine, the floor must be clean and completely dry.
Clean the floor with an automatic floor scrubber or a damp mop, using a solution
of water and neutral cleaner.
CAUTION!
This machine should be used only on floors that are coated with a floor finish
suitable for burnishing. Contact your local Advance Distributor for further
information on floor finishing products.
PREPARING THE MACHINE FOR USE
WARNING!
Moving parts - To reduce the risk of injury, unplug before servicing.
A - INSTALLING THE PAD
To install a pad, tip the machine back on it's handle. Remove the Pad Retainer
(in the center of the pad holder) by turning clockwise to loosen.
Put the proper size pad on the pad holder. Re-install the Pad Retainer by turning
counter-clockwise to tighten.
B – KNOW YOUR MACHINE
1
Operator Handle Grips
2
Switch Lever Safety Lock Button
3
Switch Levers - Squeeze - ON / Release - OFF
4
Handle Release Latch
5
Power Cord
6
Operator Handle
7
Motor Brush Wear Indicator Light
6 - FORM NO. 56041447 / SelectGloss
OPERATION
1
2
3
4
5
AFTER USE
1
2
3
4
5
6
MAINTENANCE
C - AIR FILTER
The air filter on top of the motor must be cleaned once a week. To clean the filter,
turn the motor cover counter-clockwise and remove. Pull the filter off and wash
with warm water and allow it to dry completely before putting it back on the
machine (or blow clean with compressed air).
MOTOR BRUSHES
This machine is equipped with a motor brush wear indicator light. If this light
comes on during use, contact your local Advance distributor to have the motor
serviced.
The motor can be severely damaged if the machine is used for an
extended period of time with the light glowing.
TROUBLESHOOTING
SWIRL MARKS
CIRCLES ON THE FLOOR
FLOOR FINISH REMOVED
MACHINE WOBBLES DURING OPERATION
MACHINE DOES NOT RUN
1500
Unwrap the Power Cord and plug it into a properly grounded outlet.
Unlatch the handle by pushing forward on the Handle Release Latch
with your foot. Continue to hold latch while pulling the handle back. It
is normal for the base of the machine to lift off of the floor slightly when
the handle is lowered. It will pull itself down against the floor as soon as
the motor is started.
Hold one of the Operator Hand Grips firmly, push the Safety Lock
Button and then compress the switch levers to start the motor. NOTE:
When the dual controlled switch levers are released, the machine shuts
off immediately.
Push the machine forward in a straight line, at a slow walking speed.
Overlap each pass about 1-3 inches (25-75 mm).
When using a polishing pad, check every 15 minutes to see if the pad
is loaded up with wax and dirt. If it is, turn the pad over to expose the
clean side, or install a clean pad.
Lift the Handle until it locks in the upright position.
Unplug the Power Cord and wrap it around the Handle Release Latch
and the right Operator Handle Grip.
Remove the pad from the machine. Clean the pad or brush and hang
it up to dry. Allow buffing pads to dry completely before using again.
Store brushes and pad holders separate from the machine. Never store
the machine with the pad holder or brush on the machine.
Wipe the entire machine with a clean, damp cloth.
Inspect the entire machine and all accessories for damage. Perform
any required maintenance or repairs before storage.
Store the machine in a clean, dry place with the Handle locked in the
upright position.
CAUTION!
Floor not clean.
Area not properly swept - debris in pad or brush.
Improper pad or brush for the job.
Moving the machine too fast.
Machine standing still while the brush or pad is running.
Improper pad...too aggressive.
Moving the machine too slowly.
Defective pad... one side is more dense than the other.
Machine left sitting on brush or pad for extended period of time causing
bristles or pad to "take a set".
Pad not "seated" properly into pad holder bristles.
Warped block on brush or padholder - replace.
Check plug for proper connection - on machine and at wall outlet.
Check building circuit breaker.
Call for service.

Publicidad

loading