Configuration And Selection Guide - Sundstrom SR 200 Instrucciones De Uso

III. Introduction
The Sundström SR 200 Full-face Air-purifying
Respira¬tor (APR) has been tested and approved by
NIOSH to provide the approved level of respiratory
protection to a user.
Provides limited eye protection (ANSI Z87.1-2010).
The respirator consists of an outer mask with polycar-
bonate visor that covers the user's face, an integrated
inner mask with inhalation and exhalation valves that
covers the user's nose, mouth and chin, a rubber strap
head harness with 6 mounting points that hold the
respirator in place, and a filter adapter for connecting
standard Sundström protective elements.
The inhaled air flows through a protective element and
inhalation membrane into the inner mask. Part of the
air flows past the inside of the visor in order to prevent
misting. The exhaled air is discharged from the face
piece through two exhalation valves. A laminated glass
visor, a test adapter and spectacle frames for fitting
corrective lenses are available as accessories.
This manual is divided into ten sections of equal
importance. It will provide a respirator user with the
basic information to properly use, inspect, don, doff,
and perform maintenance for the Sundström respirator.
This manual provides only the basic elements of a
complete respirator program. A well-designed respirator
program also includes fit testing, proper documentation
and active management by your local safety profes-
sional. All regulations and recommendations found in
OSHA documents, especially 29 CFR 1910.134; EPA
Standards; American National Standards Institutes
(ANSI) Standard Z88.2; and all applicable state, pro-
vincial and local regulations shall be referenced in the
complete safety program.
This respirator should not be used without thorough
understanding of all the components and their purpose.
Read this entire booklet carefully and refer to it wherever
a question arises. You must also satisfactorily complete
all regulatory and local training requirements before
entering a hazardous atmosphere.
Failure to read, understand and carefully follow
these instructions prior to using this product may
result in personal injury or death.
IV. Configuration and selection guide
FULL-FACE RESPIRATOR
Configuration, fig. 1
Component
1. Polycarbonate visor
2. Upper frame half with screws
3. Head harness assembly
4. Set of membranes
a) Exhalation membranes, two
b) Valve covers, two
c) Inhalation membranes, three
d) Dowels, two
5. Pre-filter holder
6. Filter adapter SR 280-3
7. Gasket for filter connection
8. Carry Strap
FILTER/CARTRIDGES/PRE-FILTER Order Number
OV Cartridge, SR 218-6
CL/HC/SD/FM Cartridge, SR 231
OV/SD/CL/HC/HF Cartridge, SR 232
AM/MA Cartridge, SR 229
P100 filter SR 510
Pre-filter, SR 221
ACCESSORIES
Cleaning Wipes SR 5226
Test adapter
Permanent ID tag
Visor, laminated glass
Spectacle kit for corrective lenses SR 341
Decontamination Cap
Spark Arrester, SR 336
Welding Cassette, SR 84
Protective Film, SR 343
Protective Film, SR 353
Rubber Head Harness
Protective Hood, SR 64
Protective Hood, SR 345
SmallTalk Voice Amplifier, ST2-SR
Selection of protective elements
The protective elements approved for use on the Sund-
ström Full-face Respirator are (4) chemical cartridges
and (1) particulate filter. A pre-filter is also approved for
optional use with all protective elements.
You can identify various protective elements by the
color and protection designation of the NIOSH filter/
cartridge label.
Order Number
R01-1201
R01-1202
R01-1203
R01-1204
R01-0605
H09-0212
R01-1205
R01-1206
H02-2121
H02-3621
H02-3721
H02-4321
H02-1321
H02-0121
Order Number
H09-0401
T01-1202
R09-0101
T01-1203
T01-1201
R03-1406
T01-2001
T01-1212
T01-1204
T01-1205
T01-1215
H09-0321
H09-1021
T01-1219
5