Additional Safety Instructions - EINHELL TC-SP 204 Manual De Instrucciones Original

17. Outdoor use extension cords
– When tool is used outdoors, use only exten-
sion cords intended for use outdoors and so
marked.
18. Stay alert
– Watch what you are doing. Use common
sense. Do not operate tool when you are tired.
19. Check damaged parts
– Before further use of the tool, a guard or
other part that is damaged should be care-
fully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions that may aff ect its
operation. A guard or other part that is dama-
ged should be properly repaired or replaced
by an authorized service center unless other-
wise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service center. Do not use tool
if switch does not turn it on and off .
20. Warning
– The use of any other accessory or attach-
ment other than recommended it this ope-
rating instruction or the Einhell catalog may
present a risk of personal injury.
21. Have your tool repared by an expert
– This electric appliance is in accordance with
the relevant safety rules repairing of electric
appliances may be carried out only by experts
otherwise it may cause considerable danger
for the user.
22. Connect the dust extraction device
Wherever there are facilities for fi tting a dust
extraction system, make sure it is connected
and used.

Additional safety instructions

•
Do not use blunt knives. Risk of kick-back.
•
The cutter block must be fully covered.
•
Use a push stick to plane any short workpie-
ces.
•
Take additional safety precautions if you are
planing any narrow workpieces. It may be
necessary to use lateral pressure equipment
and spring-loaded covers to ensure that you
can work in safety.
•
The machine is not suitable for cutting reba-
tes.
•
The anti-kick safeguard and the infeed roller
must be inspected at regular intervals.
•
Machines fitted with a sawdust extractor and
extractor hoods must be connected to the
devices concerned. The type of material used
Anl_SA_TC_SP_204_SPK8.indb 32 Anl_SA_TC_SP_204_SPK8.indb 32
GB
can have a negative influence on the dust ge-
nerated.
•
The machine is suitable only for cutting wood.
•
The knife must be replaced immediately once
it becomes worn down by 5%.
•
If a push stick is not used there may be a
risk of serious danger. The push stick should
always be kept at the point provided on the
left-hand side of the machine when not used.
•
There is a greater risk of danger when small
workpieces are fed in by hand. Always obser-
ve the manufacturer's instructions on the use
of the push stick.
•
If the safety covers, infeed table or mesh are
incorrectly aligned they could lead to uncont-
rollable situations.
•
Damaged or soiled workpieces may cause a
risk of danger. Never use metal parts in the
machine or any materials which can fracture
or shatter. Risk of injury!
•
To cut long workpieces, always place them
on a mobile table or similar type of supporting
equipment. Otherwise there is a risk that you
may lose control over the workpiece.
•
The machine is only suitable for planing and
thicknessing.
•
Wear suitable protective clothing when wor-
king with the machine.
- ear protection to prevent damage to your
ears,
- a breathing mask to avoid the risk of inhaling
hazardous particles of dust,
- Safety gloves when handling the knife shaft
and rough materials in order to avoid injuries
from sharp edges or knives,
- safety goggles to avoid eye injuries from
flying parts.
•
It is imperative that the following situations are
avoided at all times: Premature interruption of
the cutting operation (planing cuts which do
not complete the entire length of the workpi-
ece; planing of uneven pieces of wood which
do not lie flat on the infeed table).
•
The machine is designed for private use only.
It is prohibited to use the machine for profes-
sional or commercial use.
•
Residual risk: Bear in mind that there is
always the possibility of residual risks asso-
ciated with the use of the machine even if
you comply with all the safety instructions. By
complying with these instructions and taking
suitable care when using the machine you
will reduce the risk of injury or of damage to
the machine. Particular risks:
- 32 -
09.05.2019 10:28:31 09.05.2019 10:28:31