Layout And Items Supplied - EINHELL TC-SP 204 Manual De Instrucciones Original

- Injuries to fingers or hands from parts of the
machine or from workpieces, e.g. when chan-
ging the planing knife
- Risk of electric shock if you use power con-
nections which do not comply with standards
- Contact with conductive parts on opened
electrical components
- Hearing impairments if you work for lengthy
periods without ear protection
- Emission of hazardous sawdust if a dust
extractor is not used. Even if all safety precau-
tions are complied with it is still possible for
some residual risks to remain.
•
If the primary mains connection is in a poor
condition there is a risk of short-circuits when
the machine is switched on. This may also
affect other functions (e.g. the lighting up of
indicator lamps). Should there be any faults in
the primary mains connection, please contact
your local electricity supplier to advice and
information.
•
If the blade is fastened and positioned in-
correctly this may result in the blade being
flung out, which may be a cause of danger.
Therefore, before operation, make sure that
the blade is correctly fitted and adjusted in
accordance with the operating instructions.
•
Every part of the blade shaft not used for pla-
ning must be covered.
•
Check the machine and carry out required
maintenance work on it each time before you
start it up. In particular, inspect all the anti-
kick claws and the infeed drive shaft.
•
Make sure that the dust extraction system
and collector are connected and are used
correctly.
•
Make sure that the dust extraction system is
suitable. Fine sawdust may not only be harm-
ful to health, in certain concentrations it can
also be potentially explosive.
•
Always switch off the machine and pull out
the mains plug before making any adjust-
ments or changing settings.
•
Sawdust may cause risks to health.
•
Warning! It is prohibited to use this machine
for the following work:
- All types of work which do not cover the
whole length of the workpiece.
- Recesses, tenons or indentations
- Planing of heavily curved pieces of wood
which do not have sufficient contact with the
infeed table.
•
Use knives that are well sharpened and main-
tained.
•
Only use knives that are designed for the ma-
Anl_SA_TC_SP_204_SPK8.indb 33 Anl_SA_TC_SP_204_SPK8.indb 33
GB
chine.
•
Always stand at the side of the machine when
working.
•
In case of blocked workpieces:
- Switch off the equipment and pull out the
power plug
- Wear work gloves to prevent injury when
removing blocked workpieces.
Please keep these safety instructions in a
safe place.

2. Layout and items supplied

2.1 Layout (Fig. 1,3,5,6,11)
1 On/Off switch
2 Slide block
3 Push stick
4 Hand crank
5 Chip extractor
6 Parallel stop
7 Clamping lever
8 Mounting for planing knife cover
9 Setting knob for the chip depth
10 Workpiece support
11 Rubber foot
12 Planing knife cover
13 Feed table
14 Planing table
15 Blade adjustment block
16 Hexagon wrench - small
17 Open-ended spanner
18 Scale
19 Pointer
20 Thicknessing table
21 Blade
22 Latch
23 Knife block
24 Anti-kick claws
25 Mounting
26 Hexagon wrench - medium
27 Chip extractor adapter Ø 100 mm
28 Hexagon wrench - large
29 Scale
30 Pointer
31 Locking knob
32 Locking knob
33 Nut, self-locking
34 Securing screw for chip extractor
35 Overload switch
36 Washer
37 Hexagon screw, short
38 Scale
39 Pointer
- 33 -
09.05.2019 10:28:31 09.05.2019 10:28:31