Maintenance And Care - Schumacher Electric SJ3 Manual Del Usuario

USING THE WORK LIGHT
The work light is controlled by a sliding
ON/OFF switch located on the front of
the portable power. Make sure the lamp
is turned OFF when the unit is being
recharged or stored.
Position the portable power on a flat, stable
surface near the intended work area.
Ensure the battery clamps are securely
clipped on the storage holders.
POWERING A 12V DC DEVICE
The portable power is a power source for
all 12V DC accessories that are equipped
with a 12V accessory plug. Use it for power
outages and on fishing or camping trips.
NOTE: Do not power a 12V device with
the portable power while charging the
internal battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2. Open the protective cover of the DC
power outlet on the portable power .
3. Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
4. When finished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the portable power
to run appliances that draw more than
15A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery
drain. Recharge the portable power
immediately after unplugging the 12V
DC device.

6. MAINTENANCE AND CARE

• Clean the clips and the case each time
you are finished using it.
• Recharge the unit once a month when
not in use.
Estimated run-times
APPLIANCE
TYPE
Cell phone
Fluorescent
light
Radios, fans
Depth finder
Camcorder
Electrical tool 24 watts
Electric cooler 48 watts
Car vacuum,
air compressor 80 watts
NOTE: Actual time may vary. Times are based on the
internal battery being fully charged.
USING THE AIR COMPRESSOR
(Model SJ6)
WARNING. Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer's recommended
pressures. Do not leave the air
compressor unattended during use.
1. Remove the air compressor hose from
the storage cleats.
2. Connect the adapter to the valve stem
by threading it onto the end. If necessary,
use one of the additional adapters.
3. Turn ON the inflator power switch and
inflate to the desired pressure or fullness.
NOTE: To prevent overheating, the
compressor has built-in thermal protection
that will turn the compressor off before it
overheats. If the compressor shuts off,
wait a few minutes and it will automatically
restart when the compressor cools.
4. When the desired pressure is
reached, put the inflator power switch
to OFF, unthread the connector from
the valve stem.
5. Wrap the compressor hose around
these cleats when it is not being used.
6. Allow unit to cool.
7. Recharge the unit before storing.
NOTE: The air compressor is rated for
150 PSI.
Estimated time for inflating
Vehicle tires 13-16"
Bike tires
Sports balls
These times are approximate. Use the air compressor
gauge to ensure the proper pressure has been
reached. Do not overinflate.
• Store clips on their support posts, to
ensure they do not come into contact
with any metallic surface.
• Never completely discharge the internal
battery.
• 6 •
EST
SJ3 SJ5
WATTAGE
4 watts 13 hrs 19 hrs
4 watts 15 hrs 21 hrs
9 watts 6.7 hrs 9.3 hrs
9 watts 6.7 hrs 9.3 hrs
15 watts 4 hrs 5.6 hrs
2.5 hrs 3.5 hrs
1.3 hrs 1.8 hrs
0.8 hrs 1.1 hrs
6-24 minutes
1-3 minutes
30 seconds
SJ6
34 hrs
34 hrs
14 hrs
14 hrs
7 hrs
5 hrs
2 hours
1.8 hrs