Eliminating Faults - Festo DAPS R F Serie Instrucciones De Utilizacion

10

Eliminating faults

• Please contact Festo.
11 Technical specifications
Size Single-acting drives
Switching time per cycle
DAPS-0008-... –
DAPS-0015-... 0.2
DAPS-0030-... 0.5
DAPS-0053-... 0.9
DAPS-0060-... –
DAPS-0090-... 1.3
DAPS-0106-... –
DAPS-0120-... 1.7
DAPS-0180-... 2.7
DAPS-0240-... 3.7
DAPS-0360-... 3.9
DAPS-0480-... 3.1
DAPS-0720-... 5.8
DAPS-0960-... 6.3
DAPS-1440-... 19.0
DAPS-1920-... 15.0
DAPS-2880-... 19.0
DAPS-3840-... –
DAPS-4000-... 25.0
DAPS-5760-... –
DAPS-8000-... –
1) The switching times are specified in seconds and represent average values under idling conditions
Operating conditions DAPS
double-acting
1)
Work pressure [bar]
Rated operating pressure [bar]
Operating medium
Note on the operating medium
Ambient temperature [°C]
ATEX ambient temperature [°C]
Swivel angle [°]
End-position adjusting [°]
range at 0°
End-position adjusting [°]
range at 90°
Mounting position
Tubing
Materials
Drive shaft
Cover
Housing
Exceptions for devices with special marking
1)
Operating conditions DAPS
single-acting
1)
Work pressure [bar]
Rated operating pressure [bar]
Operating medium
Note on the operating medium
Ambient temperature [°C]
ATEX ambient temperature [°C]
Swivel angle [°]
End-position adjusting [°]
range at 0°
End-position adjusting [°]
range at 90°
Mounting position
Tubing
Materials
Drive shaft
Cover
Housing
1) Minimum operating pressures vary for single-acting quarter turn actuators depending upon spring
quantity
Double-acting drives
1)
[s] Switching time per cycle
0.08
0.08
0.13
–
0.2
–
0.4
–
0.6
0.8
1.2
1.6
2.7
3.1
5.5
6.0
16.0
12.0
–
16.0
22.0
DAPS- DAPS- DAPS- DAPS-
0008 0015 ... 0480 ... 2880 ...
0360 1920 5760
2.8 ... 8.4
5.6
Compressed air to ISO 8573-1:2010 [7:4:4]
Lubricated operation possible (required for continued
operation)
–20°C ... +80
–20°C ≤ Ta ≤ +60
90
– – – ±5
– ±2 ±2 ±5
as desired
dia. = 8 mm
high-alloy steel
wrought aluminium alloy
wrought aluminium alloy
DAPS- DAPS- DAPS-
0015 ... 0240 ... 1440 ...
0180 0960 1920
2.8 ... 8.4
5.6
Compressed air to ISO 8573-1:2010 [7:4:4]
Lubricated operation possible (required for continued
operation)
–20°C ... +80
–20°C ≤ Ta ≤ +60
90
– – –
±2 ±2 ±2
as desired
dia. = 8 mm
high-alloy steel
wrought aluminium alloy
wrought aluminium alloy
1)
[s]
DAPS-
8000
1 ... 7
DAPS-
2880,
4000
±5
±5