Replacement Parts; Use Proper Extension Cord; Double Insulation For Safer Operation - Hitachi C10FCH2 Manual De Instrucciones

English
7. When replacing the saw blade, always confirm that the rpm rating
of the new blade is correct for use on this tool.
8. Always shut off the power and wait for the saw blade to completely
stop rotating before doing any maintenance or adjustments.
9. Always clamp or otherwise secure the workpiece to the fence;
otherwise the workpiece might be thrust from the table and cause
bodily harm.
10. During miter or bevel cutting, always wait for the rotation of the
blade to stop completely before lifting the saw blade.
11. Always make a trial run first before attempting any new use of the
saw.
12. Always handle the saw blade with care when dismounting and
mounting it.
13. Always confirm that the workpiece is free of nails or other foreign
objects before beginning a cut.
14. Always keep your hands out of the path of the saw blade.
15. Always confirm that the lower guard is in the proper place before
using the saw.
16. Inspect the tool power cords periodically.
17. Always confirm that the proper lengths and types of extension cords
are being utilized, if necessary, before starting the tool.
18. Always confirm that the motor air vents are fully open before using
the tool.
19. Always wait until the motor has reached full speed before starting a
cut.
20. Always keep the handles dry, clean and free of oil and grease. Hold
the tool firmly when in use.
21. Always use outboard stands to provide support for long workpieces
that overhang the table of the compound miter saw.
22. Always operate the tool after ensuring the workpiece is fixed properly
with a vise assembly.
23. The operating instructions provided with the tool shall direct the
user to secure the tool to supporting structure if, during normal
operation, there is a tendency for the tool to tip over, slide, or walk
on the supporting surface.
DON'Ts
NEVER VIOLATE THE FOLLOWING RULES TO ASSURE
SAFE USE OF THIS TOOL:
1. Never operate the POWER TOOL unless you fully understand the
operating instructions contained in this Manual.
2. Never leave the POWER TOOL unattended without first unplugging
the power cord.
3. Never operate the POWER TOOL when you are tired, after you have
taken any medications, or have consumed any alcoholic beverages.
4. Never use the POWER TOOL for applications not specified in the
instruction manual.
5. Never operate the tool while wearing loose clothing, a necktie or
jewelry, or while your hair is uncovered, to protect against getting
caught in the moving machinery.
6. Never reach around the saw blade.
7. Never touch any moving parts, including the blade, while the saw is
in use.

USE PROPER EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Ampere Rating
More Not More
Than Than
0 – 6
6 – 10
10 – 12
12 – 16
WARNING:
Avoid electrical shock hazard. Never use this tool with a damaged or frayed electrical cord or extension cord.
Inspect all electrical cords regularly. Never use in or near water or in any environment where electric shock is possible.

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. "Double insulation" means that two physically
separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame
handled by the operator. Therefore, either the symbol " " or the words and "Double insulation" appear on the power tool or on the nameplate.
Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual,
including not using the power tool in wet environments.
4
8. Never remove any safety devices or blade guards; use of the tool
9. Never lock the lower guard; always confirm that it slides smoothly
10. Never damage the power cord of the tool.
11. Never attempt to move a plugged-in POWER TOOL while your finger
12. Never use the POWER TOOL if the starting switch does not turn on
13. Never use the POWER TOOL if the plastic housing or the handle is
14. Never use the POWER TOOL near flammable liquids or gases
15. Never clean plastic components with solvents because the plastic
16. Never operate the saw unless all the lower guards are in place.
17. Never raise the saw blade from the workpiece until it has first come
18. When slide cutting, never pull the handle toward the operator, since
19. Never place your limbs inside of the line next to warning sign " "
20. Never use abrasive type blades on this saw.
21. Never expose to rain or use in damp locations.
22. Never cut ferrous metals or masonry.
1. Always wear eye protection when using the compound miter saw.
2. Always keep hands out of the path of the saw blade.
3. Never operate the saw without the guards in place.
4. Never perform any freehand operation with the compound miter
5. Never reach around the saw blade.
6. Always turn off tool and wait for saw blade to stop before moving
7. Always disconnect power before changing blade or servicing.
8. Saw blade diameter is 10" (255mm).
9. No load speed is 5000/min.
10. To reduce the risk of injury, return carriage to the full rear position

REPLACEMENT PARTS

When servicing use only identical replacement parts.
Repairs should be conducted only by a Hitachi authorized service center.
MINIMUM GAGE FOR CORD SETS
Total Length of Cord in Feet (Meter)
0 – 25 26 – 50
(0 – 7.6) (7.9 – 15.2)
18 16
18 16
16 16
14 12
without them would be hazardous.
before using the tool.
is on the starting switch.
and off properly.
cracked or deformed.
because sparking can cause an explosion.
may dissolve.
to a complete stop.
this could cause the saw blade to kick up from the workpiece. Always
push the handle away from the operator in a single, smooth motion.
while the tool is being operated. This may cause hazardous
conditions.
WARNING
FOR YOUR OWN SAFETY READ THIS INSTRUCTION
MANUAL BEFORE OPERATING THE COMPOUND
MITER SAW
saw.
workpiece or changing settings.
after each crosscut operation.
51 – 100
(15.5 – 30.5)
AWG
16
14
14
Not Recommended
101 – 150
(30.8 – 45.7)
14
12
12