Standard Accessories; Maintenance And Inspection - Hitachi C9U2 Instrucciones De Manejo

Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Saw Blade (Dia. 235 mm) (mounted on tool) ................1
○ Hex. Bar wrench ...........................................................1
○ Guide ...........................................................................1
○ Wing-bolt ......................................................................1
○ Lever (short type) .........................................................1
○ Dust collector ...............................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
SPECIFICATIONS
The specifi cations of this machine are listed in the Table on
page 128.
NOTE
Due to HITACHI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Mounting the side handle
Adjusting the cutting depth
Adjusting the riving knife
Adjusting the angle of inclination
Regulating the guide
Adjusting the guide piece
Cutting line
Switch operation
Dismounting the saw blade
Mounting the Saw Blade*
Mounting the dust collector set
Adjusting the base and saw blade
to maintain perpendicularity
Selecting accessories
* Washer (A) is supplied for 2 types of saw blades with the
hole diameters of 16 mm and 30 mm.
(When buying the Circular Saw, one type of washer (A) is
supplied.)

MAINTENANCE AND INSPECTION

1. Inspecting the saw blade
2. Inspecting the mounting screws
3. Maintenance of the motor
4. Inspecting the carbon brushes (Fig. 14)
CAUTION
○ When replacing the new carbon brushes, always
○ For model C9BU2, the brake may not work if other than
5. Replacing carbon brushes
6. Replacing supply cord
7. Maintenance of the lower guard
Figure Page
2 129
3 129
4 129
5 129
CAUTION
In the operation and maintenance of power tools, the safety
6 129
regulations and standards prescribed in each country must
7 130
be observed.
8 130
9 130
GUARANTEE
We guarantee Hitachi Power Tools in accordance with
10 130
statutory/country specifi c regulation. This guarantee does
11 131
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
12 131
the Power Tool, undismantled, with the GUARANTEE
13 131 CERTIFICATE found at the end of this Handling instruction,
to a Hitachi Authorized Service Center.
― 132
5
Since use of as dull saw blade will degrade effi ciency
and cause possible motor malfunction, sharpen or
replace the saw blade as soon as abrasion is noted.
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
The motor unit winding is the very "heart" of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brushes with new ones having the same carbon brush
No. ⓐ shown in the fi gure when it becomes worn to or
near the "wear limit" ⓑ. In addition, always keep carbon
brushes clean and ensue that they slide freely within the
brush holders.
use genuine Hitachi carbon brushes with the number
specifi ed in the drawing.
the specifi ed carbon brushes are used.
When the brake becomes ineff ective, replace the carbon
brushes with new ones.
Disassemble the brush caps with a slotted-head
screwdriver. The carbon brushes can then be easily
removed.
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer of this agent in order
to avoid a safety hazard.
For safe and proper working, always keep the machine
and ventilation slots clean. The lower guard must
always be able to move freely and retract automatically.
Therefore, always keep the area around the lower guard
clean. Remove dust and chips by blowing out with
compressed air or with a brush.
English